Saprykina Natalia A. 2017 no. 3(76)

ОБРАБОТКА МЕТАЛЛОВ № 3 (76) 2017 16 ТЕХНОЛОГИЯ 2. Shishkovskii I.B. Selektivnoe lazernoe spekanie i sintez funktsional’nykh struktur. Diss. dokt. fiz.-mat. nauk [Selective laser sintering and synthesis of functional structures. Dr. phys.-math. sci. diss.]. Samara, 2006. 390 p. 3. Agarwala M., Bourell D., Beaman J., Marcus H., Barlow J. Direct selective laser sintering of metals. Rapid Prototyping Journal , 1995, vol. 1, iss. 1, pp. 26–36. doi: 10.1108/13552549510078113. 4. Mumtaz K., Hopkinson N. Top surface and side roughness of Inconel 625 parts processed using selective laser melting. Rapid Prototyping Journal , 2009, vol. 15, iss. 2, pp. 96–103. doi: 10.1108/13552540910943397. 5. Brecher C., ed. Integrative production technology for high-wage countries . Berlin, Springer-Verlag Berlin Heidelberg, 2012. 1096 p. ISBN 978-3-642-21066-2. doi: 10.1007/978-3-642-21067-9. 6. Gibson I.B., Rosen D.W., Stucker B. Additive manufacturing technologies: rapid prototyping to direct digital manufacturing . New York, USA, Springer, 2009. 459 p. ISBN-10: 1441911197. ISBN-13: 9781441911193. 7. Wang D., Liu Y., Yang Y., Xiao D. Theoretical and experimental study on surface roughness of 316L stainless steel metal parts obtained through selective laser melting. Rapid Prototyping Journal , 2016, vol. 22, iss. 4, pp. 706– 716. doi: 10.1108/RPJ-06-2015-0078. 8. Cheng B., Shrestha S., Chou K. Stress and deformation evaluations of scanning strategy effect in selective laser melting. Additive Manufacturing , 2016, vol. 12, pt. B, pp. 240–251. doi: /10.1016/j.addma.2016.05.007. 9. Tian Y., Tomus D., Rometsch P., Wu X. Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting. Additive Manufacturing , 2017, vol. 13, pp. 103–112. doi: 10.1016/j. addma.2016.10.010. 10. Kruth J., Wang X., Laoui T., Froyen L. Lasers and materials in selective laser sintering. Assembly Automation , 2003, vol. 23, iss. 4, pp. 357–371. doi: 10.1108/01445150310698652. 11. Jhabvala J., Boillat E., Glardon R. Study of the inter-particle necks in selective laser sintering. Rapid Prototyping Journal , 2013, vol. 19, iss. 2, pp. 111–117. doi: 10.1108/13552541311302969. 12. Kruth J.P., Froyen L., Vaerenbergh J. Van, Mercelis P., Rombouts M., Lauwers B. Selective laser melting of iron-based powder. Journal of Materials Processing Technology , 2004, vol. 149, iss. 1–3, pp. 616–622. doi: 10.1016/j. jmatprotec.2003.11.051. 13. Saprykin A.A, Saprykina N.A. Engineering support for improving quality of layer-by-layer laser sintering. Proceedings – 2012 7th International Forum on Strategic Technology , IFOST 2012, Tomsk, 18–21 September 2012, p. 6357719. doi: 10.1109/IFOST.2012.6357719. 14. Saprykina N.A., Saprykin A.A., Arkhipova D.A., Borovikov I.F. Improvement of the sintered surface and bulk of the product via differentiating laser sintering (melting) modes. IOP Conference Series: Materials Science and Engineering , 2016, vol. 142, no. 1, p. 012089. doi: 10.1088/1757-899X/142/1/012089. 15. Spiridonov A.A. Planirovanie eksperimenta pri issledovanii tekhnologicheskikh protsessov [Experiment planning in the study of technological processes]. Moscow, Mashinostroenie Publ., 1981. 184 p. © 2017 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/ ).