Eremeykin P.A. et al. 2018 Vol. 20 No. 1

OBRABOTKAMETALLOV Vol. 20 No. 1 2018 30 TECHNOLOGY Empirical Evaluation of Technological Deformations for “Soft” Cutting Modes During Thin-Walled Parts Turning Petr Eremeykin 1, a,* , Ayagma Zhargalova 2, b , Sergei Gavriushin 1, 2, c 1 Mechanical Engineering Research Institute of the Russian Academy of Sciences, 4 Maly Kharitonievskiy Pereulok, Moscow, 101990, Russian Federation 2 Bauman Moscow State Technical University, 5 Baumanskaya 2-ya, Moscow, 105005, Russian Federation a https://orcid.org/0000-0001-6291-8309 , eremeykin@gmail.com , b https://orcid.org/0000-0002-6251-1004 , azhargalova@bmstu.ru , c https://orcid.org/0000-0002-6547-1351 , gss@bmstu.ru Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2018 vol. 20 no. 1 pp. 22–32 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2018-20.1-22-32 Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov ARTICLE INFO Article history : Received: 15 December 2017 Revised: 17 January 2018 Accepted: 15 February 2018 Available online: 15 March 2018 Keywords : Cutting modes definition Turning Technological deformation Thin-walled workpiece Software Experiment Cutting modes Acknowledgements : The authors are grateful to Vitalij Semisalov and Vladimir Komarov for technical assistance. Funding : The work was carried out within grant: “Automation of technical systems and technological processes monitoring within the concept of digital manufacturing” No. 2.7918.2017 / 8.9. ABSTRACT Introduction. The problem of thin-walled parts processing is actual for various areas: aviation and space industries, power machine building and others. The literature review shows that modern methods of thin-walled parts processing suppose applying additional technological equipment that increases product cost. Recently the researchers have suggested a “soft” cutting modes method, which proposes a rational pick of cutting and clamping parameters. The method allows parts processing without additional equipment due to the effective selection of the technological process parameters (feed, rotation frequency, cutting depth) based on deformations numerical modeling. In previous papers, researchers described a computer system which allows a technologist superficially estimate the applicability of the chosen cutting modes and take the suppleness into account. Due to this system, a technologist is able to pick the parameters to minimize deformation of the workpiece before the processing starts. The purpose of the paper is to estimate the efficiently of the developed software. The article considers the case of a hollow cylindrical workpiece clamped by a three-jaw chuck. The methods of investigation: the experiment was carried out on a dedicated facility, constructed on the basis of a lathe. A dial gauge was used to measure deformations in predefined points on the workpiece surface. Results and Discussion. The experimental results are presented as deflection graphs. The graphs show both theoretical and experimental curves for various sections of the workpiece. The behavior and periodicity of the experimental curves fit the theoretical. The conducted experiments show that the developed software system is effective and reliable. For citation: Eremeykin P.A., Zhargalova A.D., Gavriushin S.S. Raschetno-eksperimental’naya otsenka tekhnologicheskikh deformatsii pri «myagkikh» rezhimakh tokarnoi obrabotki tonkostennykh detalei [Empirical evaluation of technological deformations for “soft” cutting modes during thin-walled parts turning]. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science , 2018, vol. 20, no. 1, pp. 22–32. doi: 10.17212/1994-6309-2018-20.1-22-32. (In Russian). ______ * Corresponding author Eremeykin Petr A. , post-graduate student Mechanical Engineering Research Institute of the Russian Academy of Sciences, 4 Maly Kharitonievskiy Pereulok, 101990, Moscow, Russian Federation Tel.: 8 (916) 662-57-38, e-mail: eremeykin@gmail.com