Shamarin N.N. et. al. 2020 Vol. 22 No. 1

OBRABOTKAMETALLOV Vol. 22 No. 1 2020 109 MATERIAL SCIENCE явно выраженной УМЗ - структуры после АВС - прессования и последующей прокатки приво - дит к существенному снижению шероховатости поверхности . Комплексный положительный эффект ИПД достигается за счет повышения прочности и твердости коррозионно - стойкой стали , а также улучшения качества ее обработки . Список литературы 1. Shintani T., Murata Y. Evaluation of the dislocation density and dislocation character in cold rolled Type 304 steel determined by pro fi le analysis of X-ray diffraction // Acta Materialia. – 2011. – Vol. 59. – P. 4314–4322. – DOI: 10.1016/j.actamat.2011.03.055. 2. Microstructure evolution in nano/submicron grained AISI 301LN stainless steel / S. Rajasekhara, L.P. Karjalainen,A. Kyröläinen, P.J. Ferreira // Materials Science and Engineering: A. – 2010. – Vol. 527. – P. 1986–1996. – DOI: 10.1016/j.msea.2009.11.037. 3. Ultrahigh strength nano/ultra fi ne-grained 304 stainless steel through three-stage cold rolling and annealing treatment / G.S. Sun, L.X. Du, J. Hu, H. Xie, H.Y. Wu, R.D.K. Misra // Materials Characterization. – 2015. – Vol. 110. – P. 228–235. – DOI: 10.1016/j. matchar.2015.11.001. 4. The effect of cold rolling regime onmicrostructure and mechanical properties of AISI 304L stainless steel / A. Hedayati, A. Naja fi zadeh, A. Kermanpur, F. Forouzan // Journal of Materials Processing Technology. – 2010. – Vol. 210, N 8. – P. 1017–1022. – DOI: 10.1016/j.jmatprotec.2010.02.010. 5. Ning J. Inverse determination of Johnson – Cook model constants of ultra- fi ne-grained titanium based on chip formation model and iterative gradient search // The International Journal of Advanced Manufacturing Technology. – 2018. – Vol. 99. – P. 1131-1140. – DOI: 10.1007/s00170-018-2508-6. 6. Chertovskikh V. Cuttability of UFG titaniumBT1- 0 obtained by ECAE // Russian Engineering Research. – 2007. – Vol. 27. – P. 260–264. – DOI: 10.3103/ S1068798X0705005X. 7. Huang Y., Morehead M. Study of machining- induced microstructure variations of nanostructured/ ultra fi ne-grained copper using XRD // Journal of Engineering Materials and Technology. – 2011. – Vol. 133. – P. 021007. – DOI: 10.1115/1.4003105. 8. Surface integrity analysis when milling ultra fi ne-grained steels / A.R. Rodrigues, O. Balancin, J. Gallego, C.L.F. De Assis, H. Matsumoto, F.B. De Oliveira, S.R.D.S. Moreira, O.V. Da Silva Neto // Materials Research. – 2012. – Vol. 15. – P. 125–130. – DOI: 10.1590/S1516-14392011005000094. 9. Assis C.L.F. de, Jasinevicius R.G., Rodrigues A.R. Micro end-milling of channels using ultra fi ne-grained low-carbon steel // International Journal of Advanced Manufacturing Technology. – 2015. – Vol. 77. – P. 1155–1165. – DOI: 10.1007/s00170-014-6503-2. 10. Machining characteristics of fi ne grained AZ91 Mg alloy processed by friction stir processing / G.V.V. Surya Kiran, K.H. Krishna, S. Sameer, M. Bhargavi, B.S. Kumar, G.M. Rao, Y. Naidubabu, R. Dumpala, B.R. Sunil // Transactions of Nonferrous Metals Society of China. – 2017. – Vol. 27. – P. 804– 811. – DOI: 10.1016/S1003-6326(17)60092-X. 11. Mechanical properties andmachinability of 6061 aluminum alloy produced by equal-channel angular pressing / Y. Bayat Asl, M. Meratian, A. Emamikhah, R. Mokhtari Homami, A. Abbasi // Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. – 2015. – Vol. 229. – P. 1302–1313. – DOI: 10.1177/0954405414535921. 12. Surface roughness evaluation after machining wear resistant hard coats / K. Monkova, P. Monka, J. Cesanek, J. Matejka, V. Duchek // MATEC Web of Conferences. – 2017. – Vol. 137. – P. 03008. – DOI: 10.1051/matecconf/201713703008. 13. Study of a tap failure at the internal threads machining / P. Monka, K. Monkova, V. Modrak, S. Hric, P. Pastucha // Engineering Failure Analysis. – 2019. – Vol. 100. – P. 25–36. – DOI: 10.1016/j. engfailanal.2019.02.035. 14. Surface machining after deposition of wear resistant hard coats by high velocity oxygen fuel technology / K. Monkova, P. Monka, J. Matejka, M. Novak, J. Cesanek, V. Duchek, M. Urban // Manufacturing Technology. – 2017. – Vol. 17 (6). – P. 919–925. 15. Comparative study of chip formation in orthogonal and oblique slow-rate machining of EN 16MnCr5 steel / K. Monkova, P. Monka, A. Sekerakova, L. Hruzik, A. Burecek, M. Urban // Metals. – 2019. – Vol. 9 (6). – P. 698. – DOI: 10.3390/met9060698. 16. Филиппов А . В ., Филиппова Е . О . Объемные ультрамелкозернистые материалы от структуро - образования к формообразованию // СТИН . – 2018. – № 1. – С . 6–10. 17. Оценка 2D параметров шероховатости и волнистости поверхности после обработки резани - ем сплава АМг 2 с ультрамелкозернистой структу - рой . Ч . 1. Точение / А . В . Филиппов , С . Ю . Тарасов , Н . Н . Шамарин , О . А . Подгорных , Е . О . Филиппова // СТИН . – 2018. – № 7. – С . 20–24.