Experimental study of the relationship between the vibro-acoustic parameters of the grinding process and the macro-roughness of the treated surface

OBRABOTKAMETALLOV Vol. 23 No. 3 2021 19 TECHNOLOGY 4. Ignatyev A.A., Konovalov V.V., Kozlov D.V. Opredelenie periodichnosti pravki shlifoval’nogo kruga po vibroakusticheskim kolebaniyam [Grinding wheel dressing frequency based on vibroacoustic fl uctuations]. Vestnik Saratovskogo gosudarstvennogo tekhnicheskogo = Vestnik Saratov State Technical University , 2014, no. 1 (74), pp. 71–74. 5. Zakhezin A.M., Malysheva T.V. Opredelenie iznosa shlifoval’nogo kruga po parametram vibratsii stanka [Determination of grinding wheel wear by vibration parameters of the machine]. Vestnik YuUrGU. Seriya: Mashinostroenie = Bulletin of the South Ural State University. Series: Mechanical Engineering , 2007, no. 11, pp. 48–53. 6. Mahata S., Shakya P., Babu N.R., Prakasam P.K. In-process characterization of surface fi nish in cylindrical grinding process using vibration and power signals. Procedia CIRP , 2020, vol. 88, pp. 335–340. DOI: 10.1016/j. procir.2020.05.058. 7. Otaghvar M.H., Hahn B., Werner H., Omiditabrizi H., Bahre D. A novel approach to roundness generation analysis in centerless through-feed grinding in consider of decisive parameters of grinding gap by use of 3D kinematic simulation. Procedia CIRP , 2018, vol. 77, pp. 247–250. DOI: 10.1016/j.procir.2018.09.007. 8. Otaghvar M.H., Hahn B., Werner H., Omiditabrizi H., Bahre D. Optimization of centerless through-feed grinding using 3D kinematic simulation. Procedia CIRP , 2019, vol. 79, pp. 308–312. – DOI: 10.1016/j.procir. 2019.02.072. 9. Ahrens M., Fischer R., DagenM., Denkena B., Ortmaier T.Abrasion monitoring and automatic chatter detection in cylindrical plunge grinding. Procedia CIRP , 2013, vol. 8, pp. 374–378. DOI: 10.1016/j.procir.2013.06.119. 10. Viitala R. Minimizing the bearing inner ring roundness error with installation shaft 3D grinding to reduce rotor subcritical response. CIRP Journal of Manufacturing Science and Technology , 2020, vol. 30, pp. 140–148. DOI: 10.1016/j.cirpj.2020.05.002. 11. Ahrens M., Dagen M., Denkena B., Ortmaier T. An active damping method for chatter vibration in plunge grinding using electromagnetic actuators. Procedia CIRP , 2016, vol. 46, pp. 197–200. DOI: 10.1016/j. procir.2016.03.200. 12. Ahrens M., Damm J., Dagen M., Denkena B., Ortmaier T. Estimation of dynamic grinding wheel wear in plunge grinding. Procedia CIRP , 2017, vol. 58, pp. 422–427. DOI: 10.1016/j.procir.2017.03.247. 13. Dyakonov A.A., Ardashev D.V. Prediction of blunting area of abrasive grains on a grinding wheel. Journal of Manufacturing Science and Engineering , 2017, vol. 139 (12), art. 121004. 14. Guryanihin V.F., Arinin D.V. Vliyanie rezhimov shlifovaniya na intensivnost’ akusticheskogo signala i pokazateli protsessa kruglogo naruzhnogo vreznogo shlifovaniya [The in fl uence of grinding regimes or acoustic signal intensity and process parameters of round outside cut-in grinding]. Vestnik Ul’yanovskogo gosudarstvennogo tekhnicheskogo universiteta = Bulletin of Ulyanovsk state technical university , 2000, no. 4, pp. 79–83. 15. Guryanikhin V.F., Agafonov V.V., Pankov A.A. Upravlenie protsessom kruglogo naruzhnogo vreznogo shlifovaniya s ispol’zovaniem akusticheskogo signala [Control of the process of external circular plunge-cut grinding using an acoustic signal]. STIN = Machines and Tooling , 2009, no. 2, pp. 35–40. (In Russian). 16. Lurie G.B. Shlifovanie metallov [Metal grinding]. Moscow, Mashinostroenie Publ., 1969. 172 p. 17. Lurie G.B. Vibratsii pri shlifovanii [Vibrations during grinding]. Stanki i instrument = Machines and Tooling , 1959, no. 1, pp. 15–17. (In Russian). 18. Lurie G.B. Avtokolebaniya pri shlifovanii [Self-oscillation during grinding]. Abrazivy [Abrasives]. Moscow, TsBTI Publ., 1961, iss. 27, pp. 78–83. 19. Lopovok T.S. Volnistost’ poverkhnosti i ee izmerenie [Surface waviness and its measurement]. Moscow, Standards Publ., 1973. 184 p. 20. Raja J., Muralikrishnan B., Fu S. Recent advances in separation of roughness, waviness and form. Precision Engineering , 2002, vol. 26, pp. 222–235. DOI: 10.1016/S0141-6359(02)00103-4. 21. Molotnikov V.Ya. Tekhnicheskaya mekhanika [Technical mechanics]. St. Petersburg, Lan’ Publ., 2017. 476 p. 22. Ardashev D.V., Anel’chik D.E., Butorin G.I., D’yakonov A.A. Rezhimy rezaniya na raboty, vypolnyaemye na shlifoval’nykh i dovodochnykh stankakh s ruchnym upravleniem i poluavtomatakh [Cutting modes for work performed on grinding and lapping machines with manual control and semiautomatic devices]. Chelyabinsk, Atokso Publ., 2007. 384 p. Con fl icts of Interest The authors declare no con fl ict of interest.  2021 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/ ).