OBRABOTKAMETALLOV MATERIAL SCIENCE Том 23 № 3 2021 EQUIPMEN . INSTRUM TS Vol. 6 No. 2 2024 51. Wiercigroch M., Budak E. Sources of nonlinearities, chatter generation and suppression in metal cutting. Philosophical Transactions of the Royal Society A, 2001, vol. 359 (1781), pp. 663–693. DOI: 10.1098/rsta.2000.0750. 52. Wiercigroch M., Krivtsov A.M. Frictional chatter in orthogonal metal cutting. Philosophical Transactions of the Royal Society A, 2001, vol. 359 (1781), pp. 713–738. DOI: 10.1098/rsta.2000.0752. 53. Rusinek R., Wiercigroch M., Wahi P. Influence of tool flank forces on complex dynamics of a cutting process. International Journal of Bifurcation and Chaos, 2014, vol. 24 (9), pp. 189–201. DOI: 10.1142/S0218127414501156. 54. Rusinek R., Wiercigroch M., Wahi P. Modeling of frictional chatter in metal cutting. International Journal of Mechanical Sciences, 2014, vol. 89, pp. 167–176. DOI: 10.1016/j.ijmecsci.2014.08.020. 55. Shao Y.-F., Ding H. Evaluation of gravity effects on the vibration of fluid-conveying pipes. International Journal of Mechanical Sciences, 2023, vol. 248 (5), p. 108230. DOI: 10.1016/j.ijmecsci.2023.108230. 56. Zakovorotny V.L., Gubanova A.A., Lukyanov A.D. Attractive manifolds in end milling. Russian Engineering Research, 2017, vol. 37 (2), pp. 158–163. 57. Zakovorotnyi V.L., Bykador V.S. Сutting-system dynamics. Russian Engineering Research, 2016, vol. 36 (7), pp. 591–598. DOI: 10.3103/S1068798X16070182. 58. Zakovorotniy V.L., Pham D.T., Pham T.H. Parametricheskie yavleniya pri upravlenii protsessami obrabotki na stankakh [Parametrical phenomena under on-machine process control]. Vestnik Donskogo gosudarstvennogo tekhnicheskogo universiteta = Vestnik of Don State Technical University, 2012, vol. 12, no. 7, pp. 52–61. 59. Zakovorotny V.L., Gvindjiliya V.E. Vliyanie vibratsii na traektorii formoobrazuyushchikh dvizhenii instrumenta pri tochenii [The influence of the vibration on the tool shape-generating trajectories when turning]. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2019, vol. 21, no. 3, pp. 42–58. DOI: 10.17212/1994-6309-2019-21.3-42-58. 60. Zakovorotny V.L., Gvindzhiliya V.E. Influence of spindle wobble in turning on the workpiece’s surface topology. Russian Engineering Research, 2018, vol. 38, pp. 818–823. DOI: 10.3103/S1068798X18100192. 61. Zakovorotniy V., Pham D., Nguyen X. Modelirovanie i identifikatsiya inertsionnykh i dissipativnykh svoistv podsistem rezhushchego instrumenta i zagotovki pri tochenii [Modeling and identification of inertial and dissipative properties of subsystems of cutting tool and workpiece in turning]. Vestnik Donskogo gosudarstvennogo tekhnicheskogo universiteta = Vestnik of Don State Technical University, 2010, vol. 10 (8), pp. 1165–1178. Conflicts of Interest The authors declare no conflict of interest. 2024 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0).
RkJQdWJsaXNoZXIy MTk0ODM1