OBRABOTKAMETALLOV MATERIAL SCIENCE Vol. 26 No. 2 2024 14. Grigor’yants A.G., MisyurovA.I., Tretyakov R.S. Analiz vliyaniya parametrov koaksial’noi lazernoi naplavki na formirovanie valikov [Analysis of the coaxial laser surface coating condition influence on the bead formation]. Tekhnologiya mashinostroeniya, 2011, no. 11, pp. 19–21. (In Russian). 15. OST 1-90013–81. Industry standard. Titanium alloys. Stamps. Moscow, VIAM Publ., 1981. 7 p. (In Russian). 16. Gibson I., Rosen D., Stucker B., Khorasani M. Additive manufacturing technologies. 3rd ed. Cham, Switzerland, Springer, 2021. DOI: 10.1007/978-3-030-56127-7. 17. Lewandowski J.J., Seifi M. Metal additive manufacturing: a review of mechanical properties. Annual Review of Materials Research, 2016, vol. 46, pp. 151–186. DOI: 10.1146/annurev-matsci-070115-032024. 18. De Oliveira U., Ocelik V., De Hosson J.T.M. Analysis of coaxial laser cladding processing conditions. Surface and Coatings Technology, 2005, vol. 197 (2–3), pp. 127–136. DOI: 10.1016/j.surfcoat.2004.06.029. 19. Harooni A., Nasiri A.M., Gerlich A.P., Khajepour A., Khalifa A., King J.M. Processing window development for laser cladding of zirconium on zirconium alloy. Journal of Materials Processing Technology, 2016, vol. 230, pp. 263–271. DOI: 10.1016/j.jmatprotec.2015.11.028. 20. Gladkovsky S.V, Veselova V.E, Patselov A.M, Khotinov V.A. Vliyanie deformatsionnoi stabil’nosti b-fazy v titanovom splave VT23 na fazovyi sostav, strukturu i mekhanicheskie svoistva pri rastyazhenii i udarnom izgibe [The influence of deformation stability of β-phase in titanium alloy BT23 on the phase composition, microstructure and mechanical properties after tension test and impact test]. Vestnik Permskogo natsional’nogo issledovatel’skogo politekhnicheskogo universiteta. Mashinostroenie, materialovedenie = Bulletin PNRPU. Mechanical engineering, materials science, 2019, vol. 21, no. 4, pp. 26–33. 21. Shvecov O.V., Kondratyev S.Yu. Vliyanie rezhimov zakalki i stareniya na ekspluatatsionnye svoistva splava VT23 [Effect of quenching and aging modes on the performance properties of the ВТ23 alloy]. Nauchno-tekhnicheskie vedomosti SPbPU. Estestvennye i inzhenernye nauki = St. Petersburg Polytechnic University Journal of Engineering Science and Technology, 2018, vol. 24, no. 2, pp. 119–133. 22. Wang T., Zhu Y.Y., Zhang S.Q., Tang H.B., Wang H.M. Grain morphology evolution behavior of titanium alloy components during laser melting deposition additive manufacturing. Journal of Alloys and Compounds, 2015, vol. 632, pp. 505–513. DOI: 10.1016/j.jallcom.2015.01.256. 23. ZhuY., Tian X., Li J., Wang H. Microstructure evolution and layer bands of laser melting deposition Ti–6.5Al– 3.5Mo–1.5Zr–0.3Si titanium alloy. Journal of Alloys and Compounds, 2014, vol. 616, pp. 468–474. DOI: 10.1016/j. jallcom.2014.07.161. Conflicts of Interest The authors declare no conflict of interest. 2024 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0).
RkJQdWJsaXNoZXIy MTk0ODM1