Vol. 26 No. 4 2024 5 CONTENTS OBRABOTKAMETALLOV TECHNOLOGY Manikanta J.E., Ambhore N., Shamkuwar S., Gurajala N.K., Dakarapu S.R. Investigation of vegetable-based hybrid nanofl uids on machining performance in MQL turning........................................................................................... 6 Dama Y.B., Jogi B.F., Pawade R., Kulkarni A.P. Impact of print orientation on wear behavior in FDM printed PLA Biomaterial: Study for hip-joint implant...................................................................................................................... 19 GrinenkoA.V., ChumaevskyA.V., Sidorov E.A., Utyaganova V.R.,AmirovA.I., Kolubaev E.A. Geometry distortion, edge oxidation, structural changes and cut surface morphology of 100mm thick sheet product made of aluminum, copper and titanium alloys during reverse polarity plasma cutting...................................................................................... 41 Somatkar A., Dwivedi R., Chinchanikar S. Comparative evaluation of roller burnishing of Al6061-T6 alloy under dry and nanofl uid minimum quantity lubrication conditions............................................................................................... 57 Karlina Yu.I., Konyukhov V.Yu., Oparina T.A. Assessment of the quality and mechanical properties of metal layers from low-carbon steel obtained by the WAAM method with the use of additional using additional mechanical and ultrasonic processing..................................................................................................................................................... 75 EQUIPMENT. INSTRUMENTS Yusubov N.D., Abbasova H.M. Systematics of multi-tool setup on lathe group machines............................................... 92 Toshov J.B., Fozilov D.M., Yelemessov K.K., Ruziev U.N., Abdullayev D.N., Baskanbayeva D.D., Bekirova L.R. Increasing the durability of drill bit teeth by changing its manufacturing technology......................................................... 112 Pospelov I.D. Investigation of the distribution of normal contact stresses in deformation zone during hot rolling of strips made of structural low-alloy steels to increase the resistance of working rolls..................................................... 125 Ablyaz T.R., Blokhin V.B., Shlykov E.S., Muratov K.R., Osinnikov I.V. Manufacturing of tool electrodes with optimized confi guration for copy-piercing electrical discharge machining by rapid prototyping method.......................... 138 MATERIAL SCIENCE Shubert A.V., Konovalov S.V., Panchenko I.A. A review of research on high-entropy alloys, its properties, methods of creation and application.................................................................................................................................................. 153 Syusyuka E.N., Amineva E.H., Kabirov Yu.V., Prutsakova N.V. Analysis of changes in the microstructure of compression rings of an auxiliary marine engine.......................................................................................................... 180 Dudareva A.A., Bushueva E.G., Tyurin A.G., Domarov E.V., Nasennik I.E., Shikalov V.S., Skorokhod K.A., Legkodymov A.A. The eff ect of hot plastic deformation on the structure and properties of surface-modifi ed layers after non-vacuum electron beam surfacing of a powder mixture of composition 10Cr-30B on steel 0.12 C-18 Cr-9 Ni-Ti............................................................................................................................................................................. 192 Boltrushevich A.E., Martyushev N.V., Kozlov V.N., Kuznetsova Yu.S. Structure of Inconel 625 alloy blanks obtained by electric arc surfacing and electron beam surfacing........................................................................................... 206 Sablina T.Y., Panchenko M.Yu., Zyatikov I.A., Puchikin A.V., Konovalov I.N., Panchenko Yu.N. Study of surface hydrophilicity of metallic materials modifi ed by ultraviolet laser radiation........................................................................ 218 EDITORIALMATERIALS 234 FOUNDERS MATERIALS 243 CONTENTS
RkJQdWJsaXNoZXIy MTk0ODM1