OBRABOTKAMETALLOV Vol. 23 No. 3 2021 MATERIAL SCIENCE EQUIPMENT. INSTRUMENTS 7 1 5 Development of a device for studying and simulating the electrochemical grinding process Mikhail Borisov 1, а, Dmitry Lobanov 1, b, *, Vadim Skeeba 2, c, Oksana Nadezhdina 1, d 1 I.N. Ulianov Chuvash State University, 15 Moskovsky Prospekt, Cheboksary, 428015, Russian Federation 2 Novosibirsk State Technical University, 20 Prospekt K. Marksa, Novosibirsk, 630073, Russian Federation a https://orcid.org/0000-0001-9084-1820, borisovmgou@mail.ru; b https://orcid.org/0000-0002-4273-5107, lobanovdv@list.ru; c https://orcid.org/0000-0002-8242-2295, skeeba_vadim@mail.ru; d https://orcid.org/0009-0006-3656-394X, nadezhdina_oksana@mail.ru Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2025 vol. 27 no. 1 pp. 93–105 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2025-27.1-93-105 ART I CLE I NFO Article history: Received: 26 November 2024 Revised: 12 December 2024 Accepted: 28 December 2024 Available online: 15 March 2025 Keywords: Electrochemical grinding Combined processing Modeling Abrasive tool Hybrid technology Funding This study was supported by a NSTU grant (project No. TP-PTM-1_25). Acknowledgements The research was carried out at the equipment of the Engineering Center “Design and Production of High-Tech Equipment” and the shared research facility “Structure, mechanical and physical properties of materials”. ABSTRACT Introduction. When manufacturing critical parts from high-strength and difficult-to-process steels in various industries, the final quality is usually formed during finishing operations. The efficiency of the process is significantly higher when using combined, hybrid methods of influencing the surface being processed. When processing some complex-shaped parts, more attention in finishing operations is usually paid to reducing roughness while maintaining previously achieved dimensional accuracy indicators. For this purpose, abrasive tools on a rigid base are often used, placing it in a less rigid technological system. To increase the efficiency of the process, it is necessary to establish optimal modes of mechanical and electrochemical processing of parts. In the absence of the possibility of using industrial equipment for hybrid technologies at the initial stage, taking into account the need to modernize existing technological equipment for the implementation of the electrochemical grinding process, it is advisable to study this process by simulating it on simulator devices. The purpose of the work is to develop a device for studying and simulating the process of electrochemical grinding of conductive parts with abrasive heads on a metal bond. Research methodology. To simulate the process of electrochemical grinding of conductive parts using abrasive heads on a metal bond, we have developed a special device. It allows for the basing of the workpiece and the tool, implementation the electrochemical grinding process, its kinematic and electrical conditions: main motion, linear displacement of working bodies, mechanical and electrical modes, ensuring the necessary conditions for the implementation of the technology, and implementing a control system. Results and discussion. To determine the influence of mechanical cutting modes on the roughness of the machined surface of a part made of corrosion-resistant steel 0.12 C-18Cr-10 Ni-Ti, empirical studies were carried out on the designed device. Planning and processing of experimental results were carried out using standard methodology for preparing and conducting a full factorial experiment. The resulting model makes it possible to determine rational mechanical cutting conditions and evaluate its influence on the quality of the surface being processed. For citation: Borisov M.A., Lobanov D.V., Skeeba V.Y., Nadezhdina O.A. Development of a device for studying and simulating the electrochemical grinding process. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2025, vol. 27, no. 1, pp. 93–105. DOI: 10.17212/1994-6309-2025-27.1-93-105. (In Russian). ______ * Corresponding author Lobanov Dmitry V., D.Sc. (Engineering), Associate Professor I.N. Ulyanov Chuvash State University, 15 Moskovsky Ave, 428015, Cheboksary, Russian Federation Тел.: +7 908 303-47-45, e-mail: lobanovdv@list.ru Introduction When manufacturing critical parts from high-strength and hard-to-machine steels in various industries, the final quality is typically achieved during finishing operations. These parts often operate under specific operating conditions. Consequently, they are made of hard-to-machine, corrosion-resistant, and heatresistant steels and alloys based on titanium and nickel. If there is a requirement to minimize the mass of products, many parts are thin-walled and have a complex profile.
RkJQdWJsaXNoZXIy MTk0ODM1