OBRABOTKAMETALLOV Vol. 23 No. 3 2021 MATERIAL SCIENCE EQUIPMENT. INSTRUMENTS 7 2 5 13. Thakur T., Heinen S., Ehrle B., Blugan G. Optimizing woodcutting with zirconia-toughened alumina: processing, performance, and industrial insights. Heliyon, 2025, vol. 11 (2), p. e41785. DOI: 10.1016/j.heliyon.2025. e41785. 14. Prajapati P.K., Bapanapalle C.O., Biswas P., Kumar Sadhu K., Ranjan Sahoo R., Mandal N. Cutting performance, failure mechanisms and tribological properties of MWCNT-reinforced ZTA-MgO ceramic inserts in high-speed machining of hardened AISI-4340 steel. Diamond & Related Materials, 2024, vol. 153, p. 112094. DOI: 10.1016/j.diamond.2025.112094. 15. Ghosh K., Goswami S., Kumar Prajapati P., Roy P., Mandal N. Pressure-less sintering of molybdenum-reinforced ceramic cutting inserts with improved tool life. International Journal of Refractory Metals and Hard Materials, 2024, vol. 120, p. 106619. DOI: 10.1016/j.ijrmhm.2024.106619. 16. Singh B.K., Goswami S., Ghosh K., Roy H., Mandal N. Performance evaluation of self lubricating CuO added ZTA ceramic inserts in dry turning application. International Journal of Refractory Metals and Hard Materials, 2021, vol. 98, p. 105551. DOI: 10.1016/j.ijrmhm.2021.105551. 17. Wang B., Liu Z. Influences of tool structure, tool material and tool wear on machined surface integrity during turning and milling of titanium and nickel alloys: a review. The International Journal of Advanced Manufacturing Technology, 2018, vol. 98 (5–8), pp. 1925–1975. DOI: 10.1007/s00170-018-2314-1. 18. Wang Z.G., Wong Y.S., Rahman M. High-speed milling of titanium alloys using binderless CBN tools. International Journal of Machine Tools and Manufacture, 2005, vol. 45, pp. 105–114. DOI: 10.1016/j.ijmachtools.2004.06.021. 19. Sun F.J., Qu S.G., Pan Y.X., Li X.Q., Li F.L. Effects of cutting parameters on dry machining Ti-6Al-4V alloy with ultra-hard tools. The International Journal of Advanced Manufacturing Technology, 2015, vol. 79 (1–4), pp. 351–360. DOI: 10.1007/s00170-014-6717-3. 20. Bichaud E., Chaix J.M., Carry C., Kleitz M., Steil M.C. Flash sintering incubation in Al2O3/TZP composites. Journal of the European Ceramic Society, 2015, vol. 35 (9), pp. 2587–2592. DOI: 10.1016/j.jeurceramsoc.2015.02.033. 21. Muccillo R., Muccillo E.N.S. Electric field-assisted flash sintering of tin dioxide. Journal of the European Ceramic Society, 2014, vol. 34 (4), pp. 915–923. DOI: 10.1016/j.jeurceramsoc.2013.09.017. 22. Yoshida H., Sakka Y., Yamamoto T., Lebrun J-M., Raj R. Densification behaviour and microstructural development in undoped yttria prepared by flash-sintering. Journal of the European Ceramic Society, 2014, vol. 34 (4), pp. 991–1000. DOI: 10.1016/j.jeurceramsoc.2013.10.031. 23. Srdić V.V., Winterer M., Hahn H. Sintering behavior of nanocrystalline zirconia doped with alumina prepared by chemical vapor synthesis. Journal of the American Ceramic Society, 2000, vol. 83, p. 1853. DOI: 10.1111/j.11512916.2000.tb01481.x. 24. Sakka Y., Suzuki T.S., Morita K., Nakano K., Hiraga K. Colloidal processing and superplastic properties of zirconia-and alumina-based nanocomposites. Scripta Materialia, 2001, vol. 44, p. 2075. DOI: 10.1016/S13596462(01)00889-2. 25. Rana R.P., Pratihar S.K., Bhattacharyya S. Powder processing and densification behaviour of alumina–high zirconia nanocomposites using chloride precursor. Journal of Materials Processing Technology, 2007, vol. 190 (1– 3), pp. 350–357. DOI: 10.1016/j.jmatprotec.2007.02.009. 26. Kozlov V., Zhang J.Y., Guo Y.B., Sabavath S.K. Research of contact stresses distribution on plunge-cutting into a steel workpiece. Key Engineering Materials, 2018, vol. 769, pp. 284–289. DOI: 10.4028/www.scientific.net/ KEM.769.284. Conflicts of Interest The authors declare no conflict of interest. 2025 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http:// creativecommons.org/licenses/by/4.0).
RkJQdWJsaXNoZXIy MTk0ODM1