OBRABOTKAMETALLOV MATERIAL SCIENCE Том 23 № 3 2021 EQUIPMEN . INSTRUM TS Vol. 7 No. 3 2025 formed by the cutting process and changes in the properties of force emission, represented as a random pulse sequence. The parameters of the dynamic connection formed by the cutting process depend not only on wear, but also on the technological modes and disturbances originating from the machine itself. Therefore, the use of information parameters based on changes in the vibration spectrum in the low-frequency range is relevant when processing parts in constant modes on equipment with small variations in allowance, spindle group runout, and kinematic disturbances – for example, on automatic production lines. When using these parameters on CNC machines, the diagnostic program must be coordinated with the CNC program; otherwise, the adequacy of wear representation in the spectral characteristics is significantly reduced. Force emission, considered in the high-frequency range, firstly causes changes in the intensity of force emission; secondly, shifts the intensity maximum within the frequency range; and finally, the development of wear leads to the formation of uncertainty in all parameters modeling force emission as a random pulse process, which is also an informational feature for wear diagnostic systems. References 1. Budak E. Machining process improvement through process twins. Proceedings of the 3rd International Conference on the Industry 4.0 Model for Advanced Manufacturing: AMP 2018. Springer International Publishing, 2018, pp. 164–179. DOI: 10.1007/978-3-319-89563-5_13. 2. Zakovorotny V., Gvindjiliya V. Process control synergetics for metal-cutting machines. Journal of Vibroengineering, 2022, vol. 24 (1), pp. 177–189. DOI: 10.21595/jve.2021.22087. 3. Zakovorotnyi V.L., Gvindjiliya V.E. Influence of speeds of forming movements on the properties of geometric topology of the part in longitudinal turning. Journal of Manufacturing Processes, 2024, vol. 112, pp. 202–213. DOI: 10.1016/j.jmapro.2024.01.037. 4. Zakovorotny V.L., Gvindjiliya V.E. The study of vibration disturbance mapping in the geometry of the surface formed by turning. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2024, vol. 26, no. 2, pp. 107–126. DOI: 10.17212/1994-6309-2024-26.2-107-126. 5. Ostaf’ev V.A., Antonyuk V.S., Tymchik G.S. Diagnostika protsessa metalloobrabotki [Diagnostics of the metalworking process]. Kiev, Tekhnika Publ., 1991. 152 p. ISBN 5-335-00209-3. 6. Kozochkin M.P. Mnogoparametricheskaya diagnostika tekhnologicheskikh sistem dlya obrabotki materialov rezaniem [Multivariate diagnostics of technological systems for processing materials by cutting]. Vestnik MGTU «Stankin» = Vestnik MSUT “Stankin”, 2014, no. 1 (28), pp. 13–19. 7. Grubyi S.V. Optimizatsiya protsessa mekhanicheskoi obrabotki i upravleniya rezhimnymi parametrami [Optimization of the process of mechanical processing and control of operating parameters]. Moscow, Bauman MSTU Publ., 2014. 149 p. ISBN 978-5-7038-3935-5. 8. Kabaldin Yu.G., Kuzmishina A.M., Shatagin D.A., Anosov M.S. Neironnosetevoe modelirovanie protsessa iznashivaniya tverdosplavnogo instrumenta [Neural network modeling of the wear process of a carbide cutting tool]. Avtomatizatsiya. Sovremennye tekhnologii = Automation. Modern Technologies, 2021, vol. 75, no. 9, pp. 398–402. DOI: 10.36652/0869-4931-2021-75-9-398-402. 9. Kabaldin Yu.G., Shatagin D.A., Anosov M.S., Kuzmishina A.M. Razrabotka tsifrovogo dvoinika stanka s ChPU na osnove metodov mashinnogo obucheniya [Development of digital twin of CNC unit based on machine learning methods]. Vestnik Donskogo gosudarstvennogo tekhnicheskogo universiteta = Vestnik of Don State Technical University, 2019, no. 19 (1), pp. 45–55. DOI: 10.23947/1992-5980-2019-19-1-45-55. 10. Kabaldin Yu.G., Shatagin D.A., Kuzmishina A.M. Razrabotka tsifrovogo dvoinika rezhushchego instrumenta dlya mekhanoobrabatyvayushchego proizvodstva [The development of a digital twin of a cutting tool for mechanical production]. Izvestiya vysshikh uchebnykh zavedenii. Mashinostroenie = Proceedings of Higher Educational Institutions. Machine Building, 2019, no. 4, pp. 11–17. DOI: 10.18698/0536-1044-2019-4-11-17. 11. Pantyukhin O.V., Vasin S.A. Tsifrovoi dvoinik tekhnologicheskogo protsessa izgotovleniya izdelii spetsial’nogo naznacheniya [Digital double of the technological process of manufacturing special-purpose products]. Stankoinstrument, 2021, no. 1 (22), pp. 56–59. DOI: 10.22184/2499-9407.2021.22.1.56.58. (In Russian).
RkJQdWJsaXNoZXIy MTk0ODM1