OBRABOTKAMETALLOV Vol. 23 No. 3 2021 MATERIAL SCIENCE EQUIPMENT. INSTRUMENTS 7 5 3. The following Spearman’s rank criterion (ρ) were obtained: between grain length (l) and width (b), ρ does not exceed 0.3, indicating a weak, direct correlation; between grain width (b) and shape factor (l/b), ρ ranges from −0.35 to −0.50, indicating a moderate, inverse correlation; and between grain length (l) and shape factor (l/b), ρ exceeds 0.7, indicating a strong, direct correlation. 4. Using graphical examples of the relationships between geometric parameters in fraction 2, it is demonstrated that the number of grains with a length approaching the upper size limit (l ≥ 4,650 μm) is significantly higher after roller-press grinding compared to rotary grinding. 5. Rotary grinding increases the proportion of isometric grains by an average of 5 % compared to roller-press grinding and by 8 % in the largest fraction. Roller-press grinding is characterized by a higher content of needle-shaped grains. The average content of needle-shaped grains across the five fractions is approximately 4 %. Rotary grinding reduces the number of needle-shaped grains threefold. The content of needle-shaped grains increases from larger fractions to smaller fractions and from rotary grinding to rollerpress grinding. References 1. Bogutsky V.B., Shron L.B. Izmenenie kharakteristik rabochei poverkhnosti shlifoval’nogo kruga za period ego stoikosti [Change in the characteristics of the grinding wheel face during its redress life]. Vestnik YuUrGU. Seriya: Mashinostroenie = Bulletin of the South Ural State University. Series: Mechanical Engineering, 2019, vol. 19, no. 2, pp. 66–74. DOI: 10.14529/engin190206. 2. Bratan S.M., Kharchenko A.O., Chasovitina A.S. Analiz i modelirovanie zakonomernostei izmeneniya razmerov profilei abrazivnykh zeren i ploshchadok iznosa v protsesse shlifovaniya [Analysis and modeling of patterns of changes in the size of profiles of abrasive grains and platforms wear in the grinding process]. Vestnik sovremennykh tekhnologii = Journal of Modern Technologies, 2020, no. 1, pp 43–48. 3. Chen J., Cui C., Huang G., Huang H., Xu X. Characterization of grain geometrical features for monolayer brazed grinding wheels based on grain cross-sections. The International Journal of Advanced Manufacturing Technology, 2019, vol. 105, pp. 1425–1436. DOI: 10.1007/s00170-019-04354-1. 4. Schnabel’ M., Buhr A., Schmidtmeier D., Chatterdjee S., Dutton J. Sovremennye predstavleniya o plavlenykh i spechennykh ogneupornykh zapolnitelyakh [The modern concepts of the fused and sintered refractory aggregates]. Novye ogneupory = New Refractories, 2016, no. 3, pp. 107–114. DOI: 10.17073/1683-4518-2016-3-107-114. 5. Odarchenko I.B., Prusenko I.N. Rol’ ogneupornogo napolnitelya v protsessakh strukturoobrazovaniya sterzhnevykh smesei [The role of refractory filler in the processes of structural formation of core mixtures]. Lit’e i metallurgiya = Foundry Production and Metallurgy, 2017, no. 4, pp. 89–93. 6. Yoshihara N., Takahashi H., Mizuno M. Effect of the abrasive grain distribution on ground surface roughness. International Journal of Automation Technology, 2022, vol. 16 (1), pp. 38–42. DOI: 10.20965/ijat.2022.p0038. 7. Sazonov S.E., Emchenko E.A., Strelyanaya Yu.O. Issledovanie povysheniya effektivnosti protsessa shlifovaniya krugami iz klassifitsirovannogo po forme abrazivnogo zerna [Study of increasing efficiency of the circular grinding process from classified by the form of abrasive grain]. Aktual’nye problemy v mashinostroenii = Actual Problems in Machine Building, 2020, vol. 7, no. 3–4, pp. 59–63. 8. Shatko D.B., Lyukshin V.S. Issledovanie rezhushchei sposobnosti edinichnykh abrazivnykh zeren v zavisimosti ot ikh formy i prostranstvennoi orientatsii [Investigation of cutting capacity of single abrasive grains depending on their shape and spatial orientation]. Vestnik Kuzbasskogo gosudarstvennogo tekhnicheskogo universiteta = Bulletin of the Kuzbass State Technical University, 2023, no. 5, pp. 23–30. DOI: 10.26730/1999-4125-20235-23-30. 9. Korotkov A., Korotkov V. Grinding tools made of grains with controlled shape and orientation. MATEC Web of Conferences, 2018, vol. 224, p. 01071. DOI: 10.1051/matecconf/201822401071. 10. Garshin A.P., Fedotova S.M. Abrazivnye materialy i instrumenty. Tekhnologiya proizvodstva [Abrasive materials and tools. Manufacturing technology]. St. Petersburg, Polytechnic University Publ., 2008. 1009 p. ISBN 978-5-7422-1853-1. 11. Tamás L., Rácz Á. Comparison of particle size and shape distribution of corundum produced by industrial ball mill and material bed compression. Multidiszciplináris tudományok, 2021, vol. 11, pp. 59–67. DOI: 10.35925/j. multi.2021.5.6. 12. Li Z., Zhai H., Tan M. Particle shape characterization of brown corundum powders by SEM and image analysis. IET Conference Publications, 2006, pp. 1310–1313. DOI: 10.1049/cp:20060969.
RkJQdWJsaXNoZXIy MTk0ODM1