Obrabotka Metallov 2020 Vol. 22 No. 3

OBRABOTKAMETALLOV Vol. 22 No. 3 2020 15 TECHNOLOGY Список литературы 1. Panner Selvam M., Ranjith Kumar P. Optimization kerf width and surface roughness in wirecut electrical discharge machining using brass wire // Mechanics and Mechanical Engineering. – 2017. – Vol. 21, N 1. – P. 37–55. 2. Analysis of copper mixed kerosene servotherm in EDM of Monel 400 / P.A. Anandakumar, B. Molla, F. Biruke, S. Aravind // IOP Conference Series: Materials Science and Engineering. – 2017. – Vol. 197. – P. 012004. – DOI: 10.1088/1757-899X/197/1/012004. 3. Study on cutting parameter on kerf width using wire electrical discharge machining of Inconel 718 / C.M.H. Che Nor, M. Kasim, E. Mohamad, T. Ito, M. Sulaiman // 24th Design Engineering Systems Division JSME Conference Japan Society of Mechanical Engineers. – Tokushima, Japan, 2014. – Vol. 14–27. – DOI: 10.13140/2.1.1814.7844. 4. Improve wire EDM performance at different machining parameters – ANFIS modeling / I. Maher, L.H. Ling, A.D. Sarhan, M. Hamdi // IFAC- PapersOnLine. – 2015. – Vol. 48, iss. 1. – P. 105–110. – DOI: 10.1016/j.ifacol.2015.05.109. 5. Rouniyar A.K., Shandilya P. Study on powder mixed elecrtical discharge machining process: a review // DAAAM International Scienti fi c Book. – Vienna, Austria, 2019. – Ch. 10. – P. 123–142. – DOI: 10.2507/ daaam.scibook.2019.10. 6. Relationship between occurrence of material removal and bubble expansion in electrical discharge machining / S. Hayakawa, Y. Sasaki, F. Itoigawa, T. Nakamura // Procedia CIRP. – 2013. – Vol. 6. – P. 174– 179. – DOI: 10.1016/j.procir.2013.03.095. 7. Chowdhury A.G.K., Ali M.Y., Banu A. Analysis of corner radius in dry microWEDM // International Journal of Mechanical Engineering and Robotics Research. – 2020. – Vol. 9, N 2. – DOI: 10.18178/ijmerr.9.1.158–162. 8. Özerkan H.B. Simultaneous machining and surface alloying of AISI 1040 steel by electrical discharge machining with boron oxide powders // Journal of Mechanical Science and Technology. – 2018. – Vol. 32 (9). – P. 4357–4364. – DOI: 10.1007/ s12206-018-0834-0. 9. Kinoshita N., Fukui M., Kimura Y. Study on wire- EDM: inprocess measurement of mechanical behaviour of electrode-wire // CIRP Annals – Manufacturing Technology. – 1984. – Vol. 33, N 1. – P. 89–92. – DOI: 10.1016/S0007-8506(07)61386-9. 10. Wire analysis and control for precision EDM cutting / Dauw D.F., Sthioul H., Delpretti R., Tricarico C. // CIRP Annals – Manufacturing Technology. – 1989. – Vol. 38, N 1. – P. 191–194. – DOI: 10.1016/S0007- 8506(07)62682-1. 11. Dey S., Roy D.C. Experimental study using different tools // International Journal of Modern Engineering Research (IJMER). – 2013. – Vol. 3, iss. 3. – P. 1263–1267. 12. Weingärtner E., Kuster F., Wegener K. Modeling and simulation of electrical discharge machining // Procedia CIRP. – 2012. – Vol. 2. – P. 74–78. – DOI: 10.1016/j.procir.2012.05.043. 13. Abbas N.M., Solomon D.G., Bahari Md. F. A review on current research trends in electrical discharge machining (EDM) // International Journal of Machine Tools and Manufacture. – 2007. – Vol. 47. – P. 1214– 1228. – DOI: 10.1016/j.ijmachtools.2006.08.026. 14. Yeo S.H., Kurnia W., Tan P.C. Electro-thermal modelling of anode and cathode in micro-EDM // Journal of Physics D: Applied Physics. – 2007. – Vol. 40 (8). – P. 2513–2521. – DOI: 10.1088/0022-3727/40/8/015. 15. Transient response of wire vibration system in wire electrical discharge machining / H. Yamada, N. Mohri, K. Furutani, N. Saito, T. Magara // Journal of the Japan Society for Precision Engineering. – 1997. – Vol. 63, iss. 11. – P. 1548–1552. – DOI: 10.2493/jj- spe.63.1548. 16. Шлыков Е . С . Повышение эффективности электроэрозионной обработки изделий из сталей с высокотемпературной износостойкостью : дис . … канд . техн . наук . – Пермь , 2018. – 127 с . 17. Enache S., Opran C. Dynamic stability of the technological machining system in EDM // CIRP An- nals –Manufacturing Technology. – 1993. –Vol. 42 (1). – P. 209–214. – DOI: 10.1016/S0007-8506(07)62427-5. 18. Yan M.-T., Lai Y.-P. Surface quality improvement of wire-EDM using a fi ne- fi nish power supply // Inter- national Journal of Machine Tools and Manufacture. – 2007. – Vol. 47. – P. 1686–1694. – DOI: 10.1016 /j.ij - machtools.2007.01.006. 19. Balleys F., Piantchenko Ch. Surface integrity of materials machined by wire EDM machines // EDM Technology Transfer. – 1996. – Vol. 4. – P. 3–6. 20. Kobayashi K. The present and future technologi- cal developments of EDM and ECM // Proceedings of the 11th International Symposium for Electromachining (ISEM-11). – Lausanne, Switzerland, 1995. – P. 29–47. 21. Szczesniak S. Anti-electrolysis is pro EDM // Modern Machine Shop. – 1998. – Vol. 70 (9). – P. 70–74. Конфликт интересов Авторы заявляют об отсутствии конфликта интересов .  2020 Авторы . Издательство Новосибирского государственного технического университета . Эта статья доступна по лицензии Creative Commons «Attribution» (« Атрибуция ») 4.0 Всемирная (https://creativecommons.org/licenses/by/4.0/)