Obrabotka Metallov 2021 Vol. 23 No. 3
OBRABOTKAMETALLOV Vol. 23 No. 3 2021 19 TECHNOLOGY 4. Ignatyev A.A., Konovalov V.V., Kozlov D.V. Opredelenie periodichnosti pravki shlifoval’nogo kruga po vibroakusticheskim kolebaniyam [Grinding wheel dressing frequency based on vibroacoustic fl uctuations]. Vestnik Saratovskogo gosudarstvennogo tekhnicheskogo = Vestnik Saratov State Technical University , 2014, no. 1 (74), pp. 71–74. 5. Zakhezin A.M., Malysheva T.V. Opredelenie iznosa shlifoval’nogo kruga po parametram vibratsii stanka [Determination of grinding wheel wear by vibration parameters of the machine]. Vestnik YuUrGU. Seriya: Mashinostroenie = Bulletin of the South Ural State University. Series: Mechanical Engineering , 2007, no. 11, pp. 48–53. 6. Mahata S., Shakya P., Babu N.R., Prakasam P.K. In-process characterization of surface fi nish in cylindrical grinding process using vibration and power signals. Procedia CIRP , 2020, vol. 88, pp. 335–340. DOI: 10.1016/j. procir.2020.05.058. 7. Otaghvar M.H., Hahn B., Werner H., Omiditabrizi H., Bahre D. A novel approach to roundness generation analysis in centerless through-feed grinding in consider of decisive parameters of grinding gap by use of 3D kinematic simulation. Procedia CIRP , 2018, vol. 77, pp. 247–250. DOI: 10.1016/j.procir.2018.09.007. 8. Otaghvar M.H., Hahn B., Werner H., Omiditabrizi H., Bahre D. Optimization of centerless through-feed grinding using 3D kinematic simulation. Procedia CIRP , 2019, vol. 79, pp. 308–312. – DOI: 10.1016/j.procir. 2019.02.072. 9. Ahrens M., Fischer R., DagenM., Denkena B., Ortmaier T.Abrasion monitoring and automatic chatter detection in cylindrical plunge grinding. Procedia CIRP , 2013, vol. 8, pp. 374–378. DOI: 10.1016/j.procir.2013.06.119. 10. Viitala R. Minimizing the bearing inner ring roundness error with installation shaft 3D grinding to reduce rotor subcritical response. CIRP Journal of Manufacturing Science and Technology , 2020, vol. 30, pp. 140–148. DOI: 10.1016/j.cirpj.2020.05.002. 11. Ahrens M., Dagen M., Denkena B., Ortmaier T. An active damping method for chatter vibration in plunge grinding using electromagnetic actuators. Procedia CIRP , 2016, vol. 46, pp. 197–200. DOI: 10.1016/j. procir.2016.03.200. 12. Ahrens M., Damm J., Dagen M., Denkena B., Ortmaier T. Estimation of dynamic grinding wheel wear in plunge grinding. Procedia CIRP , 2017, vol. 58, pp. 422–427. DOI: 10.1016/j.procir.2017.03.247. 13. Dyakonov A.A., Ardashev D.V. Prediction of blunting area of abrasive grains on a grinding wheel. Journal of Manufacturing Science and Engineering , 2017, vol. 139 (12), art. 121004. 14. Guryanihin V.F., Arinin D.V. Vliyanie rezhimov shlifovaniya na intensivnost’ akusticheskogo signala i pokazateli protsessa kruglogo naruzhnogo vreznogo shlifovaniya [The in fl uence of grinding regimes or acoustic signal intensity and process parameters of round outside cut-in grinding]. Vestnik Ul’yanovskogo gosudarstvennogo tekhnicheskogo universiteta = Bulletin of Ulyanovsk state technical university , 2000, no. 4, pp. 79–83. 15. Guryanikhin V.F., Agafonov V.V., Pankov A.A. Upravlenie protsessom kruglogo naruzhnogo vreznogo shlifovaniya s ispol’zovaniem akusticheskogo signala [Control of the process of external circular plunge-cut grinding using an acoustic signal]. STIN = Machines and Tooling , 2009, no. 2, pp. 35–40. (In Russian). 16. Lurie G.B. Shlifovanie metallov [Metal grinding]. Moscow, Mashinostroenie Publ., 1969. 172 p. 17. Lurie G.B. Vibratsii pri shlifovanii [Vibrations during grinding]. Stanki i instrument = Machines and Tooling , 1959, no. 1, pp. 15–17. (In Russian). 18. Lurie G.B. Avtokolebaniya pri shlifovanii [Self-oscillation during grinding]. Abrazivy [Abrasives]. Moscow, TsBTI Publ., 1961, iss. 27, pp. 78–83. 19. Lopovok T.S. Volnistost’ poverkhnosti i ee izmerenie [Surface waviness and its measurement]. Moscow, Standards Publ., 1973. 184 p. 20. Raja J., Muralikrishnan B., Fu S. Recent advances in separation of roughness, waviness and form. Precision Engineering , 2002, vol. 26, pp. 222–235. DOI: 10.1016/S0141-6359(02)00103-4. 21. Molotnikov V.Ya. Tekhnicheskaya mekhanika [Technical mechanics]. St. Petersburg, Lan’ Publ., 2017. 476 p. 22. Ardashev D.V., Anel’chik D.E., Butorin G.I., D’yakonov A.A. Rezhimy rezaniya na raboty, vypolnyaemye na shlifoval’nykh i dovodochnykh stankakh s ruchnym upravleniem i poluavtomatakh [Cutting modes for work performed on grinding and lapping machines with manual control and semiautomatic devices]. Chelyabinsk, Atokso Publ., 2007. 384 p. Con fl icts of Interest The authors declare no con fl ict of interest. 2021 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/ ).
Made with FlippingBook
RkJQdWJsaXNoZXIy MTk0ODM1