OBRABOTKAMETALLOV Vol. 25 No. 4 2023 177 MATERIAL SCIENCE Infl uence of internal stresses on the intensity of corrosion processes in structural steel Roman Sokolov a, *, Kamil Muratov b, Anatolii Venediktov c, Rasul Mamadaliev d Tyumen Industrial University, 38 Volodarskogo, Tyumen, 625000, Russian Federation a https://orcid.org/0000-0001-5867-8170, falcon.rs@mail.ru; b https://orcid.org/0000-0002-8079-2022, muratows@mail.ru; c https://orcid.org/0000-0002-6899-4297, annattoliy@gmail.com; d https://orcid.org/0000-0003-0813-0961, mamadalievra@tyuiu.ru Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2023 vol. 25 no. 4 pp. 167–179 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2023-25.4-167-179 ART I CLE I NFO Article history: Received: 09 August 2023 Revised: 21 August 2023 Accepted: 09 September 2023 Available online: 15 December 2023 Keywords: Residual internal stresses Microstructure Degree of grain anisotropy Structural steel Residual strain Corrosion rate ABSTRACT Introduction. The behavior of metal in a corrosive environment can be ambiguous, which is due to the peculiarities of the corrosion process. Both external and internal factors infl uence the corrosion process. External factors are determined by temperature, humidity, type of corrosive medium, etc., while internal factors depend on the parameters of the system (material): the presence of inclusions, phase composition, structure, and the magnitude of internal residual stresses. Internal factors ambiguously aff ect the behavior of the material in a certain aggressive medium, which ultimately aff ects the time of corrosion damage of the material and, as a consequence, the time of operation of objects made of this material. Therefore, diff erentiation of the infl uence of various internal factors on the rate of corrosion process in an aggressive environment is a priority area of research. The purpose of the present work is to consider the infl uence of the magnitude of internal residual stresses on the rate of corrosion process in an aggressive medium – 5 % sulfuric acid solution. The object of research conducted in the work is sheet rolled steel St3 as received after diff erent magnitude of plastic deformation, from which the specimens under study were made. The methods of investigation: microstructural study of deformed specimens was carried out on optical microscope Olympus GX53; software SIAMS 800 was used to compare the structure of the obtained material with the atlas of microstructures, determine the score of grain structure, determine the anisotropy of the structure after deformation of the material; X-ray diff ractometer DRON-7 was used to register diff raction patterns and determine internal stresses; laboratory scales SHIMADZU UW620h was used to measure the mass of the specimens under study; tensile strength of the material’s specimens was measured. Results and Discussion. The obtained results show that the plastic deformation of the material in the rolling direction has an ambiguous eff ect on the structure anisotropy. When the degree of plastic deformation increases, there is an ambiguous change in the grain anisotropy value, which is associated with the internal eff ects of the processes occurring in the material structure during plastic deformation, such as: sliding of the crystal lattice in the {111} <110> directions; the occurrence of reverse residual internal stresses due to the presence of inclusions in the steel structure. However, the degree of plastic deformation correlates quite well with the magnitude of internal residual stresses. The increase in the magnitude of internal residual stresses leads to an increase in the corrosion rate of structural steel St3 in 5 % hydrochloric acid solution. The obtained dependence is described by a linear equation with a high coeffi cient of determination, which indicates that there is a strong relationship between the magnitude of internal residual stresses and the rate of corrosion of the material. At the same time, the coeffi cient of infl uence of internal stresses on the corrosion rate is equal to 0.72, which additionally proves the existence of interrelation between the considered parameters. For citation: Sokolov R.A., Muratov K.R., Venediktov A.N., Mamadaliev R.A. Infl uence of internal stresses on the intensity of corrosion processes in structural steel. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2023, vol. 25, no. 4, pp. 167–179. DOI: 10.17212/1994-6309-2023-25.4-167-179. (In Russian). ______ * Corresponding author Sokolov Roman A., Post-graduate Student, Assistant Tyumen Industrial University, 38 Volodarskogo str., 625000, Tyumen, Russian Federation Tel.: +7 (919) 925-88-47, e-mail: falcon.rs@mail.ru References 1. Zhuikov I.V., Gareev D.V., Popov G.G., Bolobov V.I. [Infl uence of the stressed-deformed state of the pipeline metal on the rate of formation of grooving corrosion]. Sovremennye obrazovatel’nye tekhnologii v podgotovke spetsialistov dlya mineral’no-syr’evogo kompleksa: III Vserossiiskaya konferentsiya [Proceedings 3rd
RkJQdWJsaXNoZXIy MTk0ODM1