OBRABOTKAMETALLOV Vol. 26 No. 2 2024 54 TECHNOLOGY Investigation of cutting forces and machinability during milling of corrosion-resistant powder steel produced by laser metal deposition Artem Babaev 1, a, *, Victor Kozlov 2, b, Artem Semenov 1, c, Anton Shevchuk 1, d, Valeriia Ovcharenko2, e, Evgeniy Sudarev 2, f 1 National Research Tomsk State University, 36 Lenin Avenue, Tomsk, 634050, Russian Federation 2 National Research Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk, 634050, Russian Federation a https://orcid.org/0000-0003-2334-1679, temkams@mail.ru; b https://orcid.org/0000-0001-9351-5713, kozlov-viktor@bk.ru; c https://orcid.org/0000-0002-8663-4877, artems2102@yandex.ru; d https://orcid.org/0009-0003-5272-4350, shvpro@yandex.ru; e https://orcid.org/0009-0000-4797-5604, vag14@tpu.ru; f https://orcid.org/0000-0002-5596-4048, sudarev@tpu.ru Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2024 vol. 26 no. 2 pp. 38–56 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2024-26.2-38-56 ART I CLE I NFO Article history: Received: 11 March 2024 Revised: 30 March 2024 Accepted: 09 April 2024 Available online: 15 June 2024 Keywords: Milling Cutting forces Roughness Laser Metal Deposition Cutting modes Funding The work was carried out with fi nancial support from the Russian Science Foundation, project No. 23-79-10166 (ht tps: / / rscf . ru/en/project /23-79- 10166). The authors express their gratitude to the Russian Science Foundation for funding this work. ABSTRACT Introduction. Additive manufacturing technologies for the production of geometrically approximate workpieces require post-processing. This applies to the use of cutting tools in milling operations when machining critical surfaces. The latter are specifi ed strict requirements to accuracy of linear and angular dimensions and quality of the surface layer. An urgent task remains to increase machining productivity when recording cutting forces and surface roughness to develop technological recommendations. Purpose of work: experimental determination of cutting modes providing the highest productivity when milling LMD-workpieces (Laser Metal Deposition) made of steel 0.12-Cr18-Ni10-Ti (AISI 321) by carbide end mill, while maintaining the milling cutter operability and required roughness. The properties and microstructure of the specimens along and across the build direction are investigated. The infl uence of feed (when the mill moves across and along the build direction), depth and width of milling, speed on the components of the cutting force and roughness of the machined surfaces during counter milling of LMD-workpieces made of steel 0.12-Cr18-Ni10-Ti (AISI 321) with end mill made of H10F carbide with a diameter of 12 mm without wear-resistant coating is established and formalized. The research methods are the dynamic measurement of all three components of the cutting force using a three-component dynamometer and the measurement of roughness with a profi lometer. The condition and microgeometry of the cutting edges were monitored before and after milling using scanning optical and scanning electron microscopy. Results and Discussion. The diff erence in cutting forces depending on the milling pattern (along and across the build direction) was shown. Studies showed that the milling depth and cutting speed have little eff ect on the lateral and axial components of the cutting force. The feed force increases signifi cantly with increasing depth of cut, especially when feeding across the specimen build direction. It is found that all three components of the cutting force are directly proportional to the value of the minute feed. The equations for calculating all three components of the cutting force with a change in the minute feed are obtained. For citation: Babaev A.S., Kozlov V.N., Semenov A.R., Shevchuk A.S., Ovcharenko V.A., Sudarev E.A. Investigation of cutting forces and machinability during milling of corrosion-resistant powder steel produced by laser metal deposition. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2024, vol. 26, no. 2, pp. 38–56. DOI: 10.17212/1994-6309-202426.2-38-56. (In Russian). ______ * Corresponding author Babaev Artem S., Ph.D. (Engineering), Senior researcher National Research Tomsk State University, 36 Lenin Avenue, 634050, Tomsk, Russian Federation Тел.: +7 952 805-09-26, e-mail: temkams@mail.ru References 1. Gibson I., Rosen D., Stucker B. Additive manufacturing technologies. 2nd ed. New York, Springer Science+Business Media, 2015. 498 p. DOI: 10.1007/978-1-4939-2113-3 (Russ. ed.: Gibson Ya., Rozen D., Staker B. Tekhnologii additivnogo proizvodstva. Moscow, Tekhnosfera Publ., 2022. 648 p. ISBN 978-5-94836-447-6).
RkJQdWJsaXNoZXIy MTk0ODM1