OBRABOTKAMETALLOV Vol. 26 No. 3 2024 20 TECHNOLOGY Assembly of threaded and adhesive-threaded joints with the application of ultrasonic vibrations Aleksandr Sukhov a, *, Sergey Sundukov b, Dmitry Fatyukhin c Moscow Automobile and Road Construction State Technical University (MADI), 64 Leningradsky prospect, Moscow, 125319, Russian Federation a https://orcid.org/0009-0009-9097-8216, sukhov-aleksandr96@mail.ru; b https://orcid.org/0000-0003-4393-4471, sergey-lefmo@yandex.ru; c https://orcid.org/0000-0002-5914-3415, mitriy2@yandex.ru Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2024 vol. 26 no. 3 pp. 6–23 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2024-26.3-6-23 ART I CLE I NFO Article history: Received: 24 April 2024 Revised: 14 May 2024 Accepted: 05 June 2024 Available online: 15 September 2024 Keywords: Ultrasound Assembly Ultrasonic vibrations Threaded connection Adhesive-threaded connection Epoxy resin Funding This research was funded by the project number No. FSFM-2024-0001. ABSTRACT Introduction. The main problem in the use of threaded joints is the reduction of the preliminary force under the infl uence of workloads, which contribute to stress relaxation in the joint elements. The main directions of intensifying assembly operations in order to improve the performance properties of a threaded joint are improving the design of joints, using adhesive compositions that, after polymerization, prevent unscrewing. One of the ways to modernize the assembly is the use of ultrasonic vibrations, which makes it possible to infl uence the distribution of forces arising during assembly, as well as to process treat the adhesive to improve its properties. Research methodology. Experimental studies were carried out in three stages. At the fi rst stage, the infl uence of shear ultrasonic vibrations on the threaded joint assembly process was assessed. As a complex indicator that determines the eff ectiveness of the impact, a relative unscrewing torque is proposed, which takes into account the change in the tightening torque under vibration conditions and the increase in the unscrewing torque after assembly. At the second stage, studies were carried out on the eff ect of ultrasonic treatment on the properties of epoxy adhesive in the liquid (viscosity) and polymerized state (submicrostructure, microhardness, shear stress). At the third stage, the adhesive threaded joint was assembled with the simultaneous addition of adhesive and the application of vibrations. Results and discussion. The application of shear ultrasonic vibrations with an amplitude from 5 to 9 μm leads to an increase in the relative unscrewing torque by 1.5 times, which is associated with the creation of an additional force that promotes tightening and a decrease in friction, which acquires the characteristics of quasi-viscous. At the same time, ultrasound increases the uniformity of load distribution along the thread turns, which is confi rmed by the absence of its deformation at a higher tightening torque. Ultrasonic treatment of the adhesive at amplitudes of 8...12 μm leads to a decrease in viscosity to 70–80 % and an increase in strength to 24 %, which is explained by the action of cavitation and acoustic fl ows. The assembly of an adhesive threaded joint at vibration amplitude of 9 μm combines eff ects that promote tightening and increase the properties of the adhesive. As a result, such a connection has a relative unscrewing torque 1.95 times greater compared to the control one. For citation: Sukhov A.V., Sundukov S.K., Fatyukhin D.S. Assembly of threaded and adhesive-threaded joints with the application of ultrasonic vibrations. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2024, vol. 26, no. 3, pp. 6–23. DOI: 10.17212/1994-6309-2024-26.3-6-23. (In Russian). ______ * Corresponding author Sukhov Aleksandr V., Postgraduate student Moscow Automobile and Road Construction State Technical University (MADI), 64 Leningradsky prospect, 125319, Moscow, Russian Federation Tel.: +7 926 926-82-97, e-mail: sukhov-aleksandr96@mail.ru References 1. BerdnikovL.A. Osnovy tekhnologii proizvodstva i remontaavtomobilei. Konspekt lektsii pokursu [Fundamentals of technology for the production and repair of automobiles. Lecture notes for the course]. Nizhny Novgorod, Nizhny Novgorod State Technical University n.a. R.E. Alekseev Publ., 2015. 339 p. ISBN 978-5-502-01043-6. 2. Bobrovitskii V.I., Sidorov V.A. Mekhanicheskoe oborudovanie: tekhnicheskoe obsluzhivanie i remont [Mechanical equipment: maintenance and repair]. Donetsk, Yugo-Vostok Publ., 2011. 238 p. ISBN 978-966-374636-4.
RkJQdWJsaXNoZXIy MTk0ODM1