OBRABOTKAMETALLOV Vol. 26 No. 4 2024 88 TECHNOLOGY Assessment of the quality and mechanical properties of metal layers from low-carbon steel obtained by the WAAM method with the use of additional using additional mechanical and ultrasonic processing Yulia Karlina 1, a, *, Vladimir Konyukhov 2, b, Tatiana Oparina 2, c 1 National Research Moscow State University of Civil Engineering, 26 Yaroslavskoe Shosse, Moscow, 129337, Russian Federation 2 Irkutsk National Research Technical University, 83 Lermontova str., Irkutsk, 664074, Russian Federation a https://orcid.org/0000-0001-6519-561X, jul.karlina@gmail.com; b https://orcid.org/0000-0001-9137-9404, konyukhov_vyu@mail.ru; c https://orcid.org/0000-0002-9062-6554, martusina2@yandex.ru Obrabotka metallov - Metal Working and Material Science Journal homepage: http://journals.nstu.ru/obrabotka_metallov Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science. 2024 vol. 26 no. 4 pp. 75–91 ISSN: 1994-6309 (print) / 2541-819X (online) DOI: 10.17212/1994-6309-2024-26.4-75-91 ART I CLE I NFO Article history: Received: 14 September 2024 Revised: 08 October 2024 Accepted: 17 October 2024 Available online: 15 December 2024 Keywords: Additive Manufacturing Wire and arc additive manufacturing WAAM Wire Structure Ultrasonic hardening Hardness Yield strength Pores Gas ABSTRACT Introduction. Additive manufacturing is a technology that enables three-dimensional (3D) components to be printed layer by layer according to digital models. Completely diff erent from traditional manufacturing methods such as casting, forging, and machining, additive manufacturing is a near net shape manufacturing process that can greatly enhance design freedom and reduce manufacturing runtime. The material processing challenges in Wire and Arc Additive Manufacturing (WAAM) are related to achieving performance metrics related to geometric, physical, and material properties. Tight tolerances and stringent surface integrity requirements cannot be achieved by utilizing stand-alone AM technologies. Therefore, WAAM parts typically require some post-processing to meet requirements related to surface fi nish, dimensional tolerances and mechanical properties. It is therefore not surprising that the integration of AM with post-processing technologies into single and multi-setup machining solutions, commonly referred to as hybrid AM, has become a very attractive proposition for industry. The purpose of the work is to evaluate the quality and mechanical properties of the resulting metal layers of mild steel by WAAM method using additional mechanical and ultrasonic processing. Research Methods. To conduct the experiments, a set of welding equipment was used — a single-phase inverter device KEMPPI Kempomat 1701, designed for welding with wire in shielding gases. A mixture of argon and carbon dioxide (80 % argon and 20 % CO2) was used as a shielding gas. SV-08G2S (0.8 C-2 Mg-Si) wire was used as the surfacing material. Aplate made of steel St3 with overall dimensions 150×100×5 mm was used as a base for surfacing. The surface of the plate before surfacing was thoroughly cleaned from the layer of oxides, oil, rust and other contaminants. For this purpose mechanical cleaning of the surface was used with BOSCH abrasive wheel with a diameter of 125 mm diameter and a grit size of 120. Before surfacing the surface of the product was degreased with white spirit. The gas fl ow rate was set at 8 dm3/min. To select the optimal wire feed rate and volt-ampere characteristic, surfacing was performed at each adjustment step of wire feed rate, and voltage. Mechanical statistical tensile tests, chemical composition analysis and metallographic studies were also performed. Results and Discussion. Gas porosity is a typical defect that occurs during the WAAM process and should be eliminated because it adversely aff ects the mechanical properties. Initially, gas porosity leads to a reduction in the mechanical strength of the part due to damage from microcrack formation. In addition, it often causes the surfaced layer to have worse fatigue properties due to the spatial distribution of diff erent shape and size structures. In our experiments we found that a wire feed speed range of 5–6 m/min is optimal. Increasing the fl ow rate of shielding gas in the range of 8–14 l/min allows reducing porosity in the surfaced metal to almost zero. The mechanical properties of the surfaced beads show that the average value of yield strength after machining is higher than that of unprocessed specimens. The data obtained from these experiments are in good agreement with those reported in the literature. The presented results can be used in real WAAM technological processes. For citation: KarlinaYu.I., KonyukhovV.Yu., Oparina T.A.Assessment of the quality andmechanical properties of metal layers from low-carbon steel obtained by the WAAM method with the use of additional using additional mechanical and ultrasonic processing. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2024, vol. 26, no. 4, pp. 75–91. DOI: 10.17212/1994-63092024-26.4-75-91. (In Russian). ______ * Corresponding author Karlina Yulia I., Ph.D. (Engineering), Research Associate National Research Moscow State Construction University, Yaroslavskoe shosse, 26, 129337, Moscow, Russian Federation Tel.: +7 914 879-85-05, e-mail: jul.karlina@gmail.com
RkJQdWJsaXNoZXIy MTk0ODM1