OBRABOTKAMETALLOV Vol. 28 No. 1 2026 112 TECHNOLOGY 4. Belopukhov A.K. Tekhnologicheskie rezhimy lit’ya pod davleniem [Technological modes of die casting]. Moscow, Mashinostroenie Publ., 1985. 272 p. 5. Zhukov A.A., Nemtyrev O.V. Issledovanie teplovoi strukturnoi stabil’nosti stalei dlya press-form lit’ya pod davleniem [Research of thermal structural stability of steels for casting press moulds]. Naukoemkie tekhnologii v mashinostroenii = Science Intensive Technologies in Mechanical Engineering, 2014, vol. 4 (34), pp. 3–10. 6. Tojal M.C., Silva F.J.G., Campilho R.D.S.G., Pinto A.G., Ferreira L.P. Case-based product development of a high-pressure die casting injection subset using design science research. FME Transactions, 2022, vol. 50 (1), pp. 32–45. DOI: 10.5937/fme2201032T. 7. Gavariev R.V., Soldatkina E.N., Gavarieva K.N. Coatings and lubricant to forming surfaces of molds for casting under pressure. Solid State Phenomena, 2021, vol. 316, pp. 789–793. DOI: 10.4028/www.scientifi c.net/ssp.316.789. 8. Livshits V.B., Milchakova N.E., Berestnev A.A. Sposob uprochneniya vkladyshei press-form dlya lit’ya s kristallizatsiei pod davleniem [Method of strengthening inserts of press molds for casting with crystallization under pressure]. Liteinoe proizvodstvo = Foundry. Technology and Equipment, 2018, no. 3, pp. 30–32. 9. Bao Z.-J., Yang H.-Y., Dong B.-X., Chang F., Li C.-D., Jiang Y., Chen L.-Y., Shu S.-L., Jiang Q.-C., Qiu F. Development trend in composition optimization, microstructure manipulation, and strengthening methods of die steels under lightweight and integrated die casting. Materials, 2023, vol. 16 (18), pp. 6235. DOI: 10.3390/ma16186235. 10. Capela P., Gomes I.V., Lopes V., Prior F., Soares D., Teixeira J.C. Experimental analysis of heat transfer at the interface between die casting molds and additively manufactured cooling inserts. Journal of Materials Engineering and Performance, 2023, vol. 32 (23), pp. 10934–10942. DOI: 10.1007/s11665-023-08425-z. 11. Shin S.-S., Lee S.-K., Kim D.-K., Lee B. Enhanced cooling channel effi ciency of high-pressure die-casting molds with pure copper linings in cooling channels via explosive bonding. Journal of Materials Processing Technology, 2021, vol. 297, p. 117235. DOI: 10.1016/j.jmatprotec.2021.117235. 12. Clark L.D., Davey K., Hinduja S. Novel cooling channel shapes in pressure die casting. International Journal for Numerical Methods in Engineering, 2001, vol. 50 (10), pp. 2411–2440. DOI: 10.1002/nme.126. 13. Schuchardt T., Müller S., Dilger K. A near-surface layer heat treatment of die casting dies by means of electron-beam technology. Metals, 2021, vol. 11 (8), p. 1236. DOI: 10.3390/met11081236. 14. Gavariev R.V., Savin I.A., Leushin I.O., Gavarieva K.N. K voprosu poristosti alyuminievykh otlivok, poluchennykh lit’em pod davleniem [On the question of porosity of aluminum castings obtained by injection molding]. Tsvetnye Metally, 2021, no. 8, pp. 76–82. DOI: 10.17580/tsm.2021.08.12. (In Russian). 15. Akkaya E., Kayır Y. The eff ect of aluminium injection parameters on the mechanical properties of the material produced by high pressure die-casting. Gazi University Journal of Science, Part C: Design and Technology, 2023, vol. 11 (2), pp. 421–430. DOI: 10.29109/gujsc.1211920. 16. Yalçın B., Koru M., Ipek O., Özgür A.M. Eff ect of injection parameters and vacuum on the strength and porosity amount of die-casted A380 alloy. International Journal of Metalcasting, 2017, vol. 11 (2), pp. 195–206. DOI: 10.1007/s40962-016-0046-2. 17. Concer D., Marcondes P.V.P. Experimental and numerical simulation study of porosity on high-pressure aluminum die casting process. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2017, vol. 39, pp. 3079–3088. DOI: 10.1007/s40430-016-0672-x. 18. Nourian-Avval A., Fatemi A. Characterization and analysis of porosities in high-pressure die cast aluminum by using metallography, X-ray radiography, and micro-computed tomography. Materials, 2020, vol. 14), p. 3068. DOI: 10.3390/ma13143068. 19. Cao H., Zhang Q., Zhu W., Cui S., Yang Q., Wang Z., Jiang B. Study on the infl uence of injection velocity on the evolution of hole defects in die-cast aluminum alloy. Materials, 2024, vol. 17 (20), p. 4990. DOI: 10.3390/ ma17204990. 20. Vereshchaka A.S. Rabotosposobnost’ rezhushchego instrumenta s iznosostoikimi pokrytiyami [Performance of cutting tools with wear-resistant coatings]. Moscow, Mashinostroenie Publ., 1993. 336 p. 21. Yusubov N., Abbasova H. Full-factor matrix model of accuracy of dimensions performed on multi-purpose CNC machines. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2021, vol. 23 (4), pp. 6–20. DOI: 10.17212/1994-6309-2021-23.4-6-20. 22. Yusubov N.D., Abbasova H.M. Models of cutting forces in the matrix theory of multitool machining accuracy. Key Engineering Materials, 2024, vol. 979, pp. 27–38. DOI: 10.4028/p-bW48Sb. 23. Yusubov N., Abbasova H., Khankishiyev I. Development of a planning theory for multi-tool machining with the possibilities of modern CNC machine tools. Forschung im Ingenieurwesen, 2021, vol. 85 (2), pp. 661–678. DOI: 10.1007/s10010-021-00478-7.
RkJQdWJsaXNoZXIy MTk0ODM1