OBRABOTKAMETALLOV Vol. 28 No. 2 2026 221 EQUIPMENT. INSTRUMENTS References 1. Komanduri R. Some clarifi cations of the mechanics of chip formation when machining titanium alloys. Wear, 1982, vol. 76, pp. 15–34. DOI: 10.1016/0043-1648(82)90113-2. 2. Kozlov V.N., Zhang J.Y., Letshiner E., Zhao W.Z. Infl uence of cutting tool wear on contact stresses and temperature distribution in titanium alloy machining. Key Engineering Materials, 2017, vol. 743, pp. 252–257. DOI: 10.4028/www.scientifi c.net/KEM.743.252. 3. Kozlov V.N., Zhang J.Y. Strength of cutting tool in titanium alloy machining. Key Engineering Materials, 2016, vol. 685, pp. 427–431. DOI: 10.4028/www.scientifi c.net/KEM.685.427. 4. Liu H., Sun Y., Geng Y., Shan D. Experimental research of milling force and surface quality for TC4 titanium alloy of micro-milling. International Journal of Advanced Manufacturing Technology, 2015, vol. 79, pp. 705–716. DOI: 10.1007/s00170-015-6844-5. 5. Oliaei S.N., Karpat Y. Investigating the infl uence of built-up edge on forces and surface roughness in micro scale orthogonal machining of titanium alloy Ti6Al4V. Journal of Materials Processing Technology, 2016, vol. 235, pp. 28–40. DOI: 10.1016/j.jmatprotec.2016.04.010. 6. Feng J., Sun Z., Jiang Z., Yang L. Identifi cation of chatter in milling of Ti-6Al-4V titanium alloy thin-walled workpieces based on cutting force signals and surface topography. International Journal of Advanced Manufacturing Technology, 2016, vol. 82, pp. 1909–1920. DOI: 10.1007/s00170-015-7509-0. 7. Bogoljubova M., Afonasov A., Kozlov V., Sumtsova O. Mathematical simulation and optimization of cutting modes in turning of titanium alloy workpieces. IOP Conference Series: Materials Science and Engineering, 2016, vol. 124, p. 012045. DOI: 10.1088/1757-899X/124/1/012045. 8. Rahman M., Wang Z.G., Wong Y.S. A review on high-speed machining of titanium alloys. JSME International Journal. Series C, 2006, vol. 49, pp. 11–20. DOI: 10.1299/jsmec.49.11. 9. Li L., He N., Xu J.H. Experimental study on high speed milling of Ti alloys. Materials Science Forum, 2004, vol. 471–472, pp. 414–418. DOI: 10.4028/www.scientifi c.net/MSF.471-472.414. 10. Huang P., Li J., Sun J., Ge M. Milling force vibration analysis in high speed milling of Ti alloy using variable pitch angle mill. International Journal of Advanced Manufacturing Technology, 2012, vol. 58, pp. 153–160. DOI: 10.1007/s00170-011-3380-9. 11. Abele E., Fröhlich B. High speed milling of titanium alloys. Advances in Production Engineering & Management, 2008, vol. 3, pp. 131–140. 12. Da Silva R.B., Machado Á.R., Ezugwu E.O., Bonney J., Sales W.F. Tool life and wear mechanisms in high speed machining of Ti-6Al-4V alloy with PCD tools under various coolant pressures. Journal of Materials Processing Technology, 2013, vol. 213, pp. 1459–1464. DOI: 10.1016/j.jmatprotec.2013.03.008. 13. Wang Q., Chen X., An Q., Chen M., Guo H., He Y. Research on cutting performance and tool life improvement methods of titanium alloy ultra-high speed milling tools. Journal of Manufacturing Processes, 2024, vol. 131, pp. 38– 51. DOI: 10.1016/j.jmapro.2024.09.018. 14. Ullah I., Akinlabi E.T., Songmene V. Thermo-metallo-mechanical based phase transformation modeling for high-speed milling of Ti-6Al-4V through stress-strain and temperature eff ects. Journal of Materials Research and Technology, 2024, vol. 30, pp. 894–909. DOI: 10.1016/j.jmrt.2024.03.096. 15. Raghavendra S., Sathyanarayanab P.S., Selvakumar S., Thangarasu V.S., Manjunatha K.N. High speed machining of titaniumTi6Al4V alloy components: study and optimisation of cutting parameters using RSM. Advances in Materials and Processing Technologies, 2020, vol. 8, pp. 277–290. DOI: 10.1080/2374068X.2020.1806684. 16. Abbas A.T., Sharma N., Anwar S., Hashmi F.H., Jamil M., Hegab H. Towards optimization of surface roughness and productivity aspects during high-speed machining of Ti-6Al-4V. Materials, 2019, vol. 12, p. 3749. DOI: 10.3390/ma12223749. 17. Gao Y., Wang G., Liu B. Chip formation characteristics in the machining of titanium alloys: A review. International Journal of Machining and Machinability of Materials, 2016, vol. 18, p. 155. DOI: 10.1504/ IJMMM.2016.075467. 18. Jawaid A., Sharif S., Koksal S. Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy. Journal of Materials Processing Technology, 2000, vol. 99, pp. 266–274. DOI: 10.1016/S09240136(99)00438-0. 19. Zhang Y.P., Xu J.H., Geng G.S. Tool wear and surface integrity in high speed milling of a near alpha titanium alloy. Materials Science Forum, 2006, vol. 532–533, pp. 644–647. DOI: 10.4028/www.scientifi c.net/MSF.532533.644. 20. Elmagrabi N., Che Haron C.H., Jaharah A.G., Shuaeib F.M. High speed milling of Ti-6Al-4V using coated carbide tools. European Journal of Scientifi c Research, 2008, vol. 22, pp. 153–160.
RkJQdWJsaXNoZXIy MTk0ODM1