OBRABOTKAMETALLOV Vol. 28 No. 2 2026 98 TECHNOLOGY 22. Choi J.G., Yang M.Y. In-process prediction of cutting depths in end milling. International Journal of Machine Tools and Manufacture, 1999, vol. 39 (5), pp. 705–721. DOI: 10.1016/S0890-6955(98)00067-4. 23. Babaev A.S., Kozlov V.N., Semenov A.R., Shevchuk A.S., Ovcharenko V.A., Sudarev E.A. Issledovanie sil rezaniya i obrabatyvaemosti pri frezerovanii poroshkovoi korrozionno-stoikoi stali, poluchennoi po tekhnologii pryamogo lazernogo vyrashchivaniya (LMD) [Investigation of cutting forces and machinability during milling of corrosion-resistant powder steel producedby lasermetal deposition]. Obrabotkametallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2024, vol. 26, no. 2, pp. 38–56. DOI: 10.17212/1994-63092024-26.2-38-56. 24. Arlyapov A., Volkov S., Promakhov V., Matveev A., Babaev A., Vorozhtsov A., Zhukov A. Study of the machinability of an Inconel 625 composite with added NiTi-TiB2 fabricated by direct laser deposition. Metals, 2022, vol. 12. DOI: 10.3390/met12111956. 25. Rahman M.A., Rahman M., Woon K.S., Mia M. Episodes of chip formation in micro-to-nanoscale cutting of Inconel 625. International Journal of Mechanical Sciences, 2021, vol. 199. DOI: 10.1016/j.ijmecsci.2021.106407. 26. Li G., Xu W., Jin X., Liu L., Ding S., Li C. The machinability of stainless steel 316 L fabricated by selective laser melting: Typical cutting responses, white layer and evolution of chip morphology. Journal of Materials Processing Technology, 2023, vol. 315. DOI: 10.1016/j.jmatprotec.2023.117926. 27. Kocaman E., Gürol U., Günen A., Çam G. Eff ect of post-deposition heat treatments on high-temperature wear and corrosion behavior of Inconel 625. Materials Today Communications, 2025, vol. 42. DOI: 10.1016/ j.mtcomm.2024.111101. 28. Liu E., An W., Xu Z., Zhang H. Experimental study of cutting-parameter and tool life reliability optimization in Inconel 625 machining based on wear map approach. Journal of Manufacturing Processes, 2020, vol. 53, pp. 34– 42. DOI: 10.1016/j.jmapro.2020.02.006. 29. Yıldırım Ç.V., Sarıkaya M., Kıvak T., Şirin Ş. The eff ect of addition of hBN nanoparticles to nanofl uidMQL on tool wear patterns, tool life, roughness and temperature in turning of Ni-based Inconel 625. Tribology International, 2019, vol. 134, pp. 443–456. DOI: 10.1016/j.triboint.2019.02.027. 30. Akhtar W., Sun J., Sun P., Chen W., Saleem Z. Tool wear mechanisms in the machining of Nickel based superalloys: a review. Frontiers of Mechanical Engineering, 2014, vol. 9, pp. 106–119. DOI: 10.1007/s11465-014-0301-2. 31. Astakhov V.P. The assessment of cutting tool wear. International Journal of Machine Tools and Manufacture, 2004, vol. 44, pp. 637–647. DOI: 10.1016/j.ijmachtools.2003.11.006. 32. Ayed Y., Germain G., Ammar A., Furet B. Degradation modes and tool wear mechanisms in fi nish and rough machining of Ti17 Titanium alloy under high-pressure water jet assistance. Wear, 2013, vol. 305 (1–2), pp. 228–237. DOI: 10.1016/j.wear.2013.06.018. 33. Liu E., Wang N., Qi J., Xu Z., Liu X., Zhang H. Experimental study on the oxidation and diff usion behavior of Inconel 625 and tool materials. Crystals, 2018, vol. 8 (12). DOI: 10.3390/cryst8120471. 34. Kozlov V., Babaev A., Schulz N., Semenov A., Shevchuk A. Study of a methodology for calculating contact stresses during blade processing of structural steel. Metals, 2023, vol. 13 (12). DOI: 10.3390/met13122009. Confl icts of Interest The authors declare no confl ict of interest. © 2026 The Authors. Published by Novosibirsk State Technical University. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0).
RkJQdWJsaXNoZXIy MTk0ODM1