ОБРАБОТКА МЕТАЛЛОВ

Introduction. The problem of thin-walled parts processing is actual for various areas: aviation and space industries, power machine building and others. The literature review shows that modern methods of thin-walled parts processing suppose applying additional technological equipment that increases product cost. Recently the researchers have suggested a “soft” cutting modes method, which proposes a rational pick of cutting and clamping parameters. The method allows parts processing without additional equipment due to the effective selection of the technological process parameters (feed, rotation frequency, cutting depth) based on deformations numerical modeling. In previous papers, researchers described a computer system which allows a technologist superficially estimate the applicability of the chosen cutting modes and take the suppleness into account. Due to this system, a technologist is able to pick the parameters to minimize deformation of the workpiece before the processing starts. The purpose of the paper is to estimate the efficiently of the developed software. The article considers the case of a hollow cylindrical workpiece clamped by a three-jaw chuck. The methods of investigation: the experiment was carried out on a dedicated facility, constructed on the basis of a lathe. A dial gauge was used to measure deformations in predefined points on the workpiece surface. Results and Discussion. The experimental results are presented as deflection graphs. The graphs show both theoretical and experimental curves for various sections of the workpiece. The behavior and periodicity of the experimental curves fit the theoretical. The conducted experiments show that the developed software system is effective and reliable.

1. Machining surface quality analysis of aluminum alloy thin-walled parts in aerospace / D. Bing, Y. Guang-bin, G. Yan-qi, S. Jun-peng, W. Xue-mei, L. Yu-xin // International Journal of Security and Its Applications. – 2015. – Vol. 9, N 11. – P. 201–208. – doi: 10.14257/ijsia.2015.9.11.19.

2. Технология машиностроения. В 2 т. Т. 1. Основы технологии машиностроения / под общ. ред. А.М. Дальского. – М.: Изд-во МГТУ им. Н.Э. Баумана, 1999. – 370 с. – ISBN 978-5-7038-3442-8.

3. Кузнецов Ю.И., Мослов А.Р., Бойков А.Н. Оснастка для станков с ЧПУ: справочник. – М.: Машиностроение, 1990. – 512 с. – ISBN 5-217-01114-9.

4. Евгенев Г.Б., Гаврюшин С.С., Хоботов Е.Н. Основы автоматизации технологических процессов и производств. В 2 т. Т. 2. – М.: Изд-во МГТУ им. Н.Э. Баумана, 2015. – 479 с. – ISBN 978-5-7038-4139-6.

5. Milling error prediction and compensation in machining of low-rigidity parts / S. Ratchev, S. Liu, W. Huang, A.A. Becker // International Journal of Machine Tools & Manufacture. – 2004. – Vol. 44, iss. 15. – P. 1629–1641. – doi: 10.1016/j.ijmachtools.2004.06.001.

6. Demyanenko E.G., Popov I.P., Menshikov V.S. Research of the process of axisymmetric forming of thin-walled flat blanks into the conical parts with minimal thickness variation // International Conference on Mechanical Engineering, Automation and Control Systems, Tomsk, Russia, 27–29 October 2016. – Bristol, 2017. – Art. 012122. – (IOP conference series. Materials science and engineering; vol. 177). – doi: 10.1088/1757-899X/177/1/012122.

7. Huang Y., Zhang X., Xiong Y. Finite element analysis of machining thin-wall parts: error prediction and stability analysis // Finite element analysis – applications in mechanical engineering / ed. by F. Ebrahimi. – Rijeka, Croatia: InTech, 2004. – doi: 10.5772/50374.

8. Joshi S.N., Bolar G.J. Three-dimensional finite element based numerical simulation of machining of thin-wall components with varying wall constraints // Journal of The Institution of Engineers (India): Series C. – 2017. – Vol. 98, iss. 3. – P. 343–352. – doi: 10.1007/s40032-016-0246-9.

9. Joshi S.N., Bolar G.J. Three-dimensional numerical modeling, simulation and experimental validation of milling of a thin-wall component // Proceeding of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. – 2017. – Vol. 231, iss. 5. – P. 792–804. – doi: 10.1177/0954405416685387.

10. Scippa A., Grossi N., Campatelli G. FEM based cutting velocity selection for thin walled part machining // Procedia CIRP. – 2014 – Vol. 14. – P. 287–292. – doi: 10.1016/j.procir.2014.03.023.

11. Zienkiewicz O.C. The finite element method in engineering science. – London; New York: McGraw-Hill, 1972. – 521 p. – ISBN 978-0-0709-4138-0.

12. Bathe K.J. Finite element method procedures. – [S. l.]: Klaus-Jurgen Bathe, 2007. – 1037 p. – ISBN 978-0-9790-0490-2.

13. Izamshah R.A., Mo J.P.T., Ding S.L. Finite element analysis of machining thin-wall parts // Key Engineering Materials. – 2011. – Vol. 458. – P. 283–288. – doi: 10.4028/www.scientific.net/KEM.458.283.

14. Machining of thin-walled parts produced by additive manufacturing technologies / A. Isaev, V. Grechishnikov, P. Pivkin, M. Kozochkin, Y. Ilyuhin, A. Vorotnikov // Procedia CIRP. – 2016. – Vol. 41. – P. 1023–1026. – doi: 10.1016/j.procir.2015.08.088.

15. Shamsuddin K.A., Ab-Kadir A.R., Osman M.H. A comparison of milling cutting path strategies for thin-walled aluminium alloys fabrication // The International Journal of Engineering and Science (IJES). – 2013. – Vol. 2, iss. 3. – P. 1–8.

16. Метод определения условий механической обработки тонкостенных деталей / С.C. Гаврюшин, А.Д. Жаргалова, Г.П. Лазаренко, В.И. Семисалов // Известия высших учебных заведений. Машиностроение. – 2015. – № 11. – C. 53–61. – doi: 10.18698/0536-1044-2015-11-53-61.

17. Жаргалова А.Д., Еремейкин П.А. Программная система автоматизированного выбора режимов механической обработки тонкостенных деталей // Актуальные проблемы в машиностроении. – 2017. – Т. 4, № 1. – С. 9–14.

18. Eremeykin P.A., Zhargalova A.D., Gavriushin S.S. A software system for thin-walled parts deformation analysis // Advances in Artificial Systems for Medicine and Education / ed. by Z. Hu, S.V. Petukhov, M. He. – Cham: Switzerland Springer Nature, 2018. – P. 259–265. – (Advances in intelligent systems and computing; vol. 658). – doi: 10.1007/978-3-319-67349-3_24.

19. Еремейкин П.А., Жаргалова А.Д., Лазаренко Г.П. Интегрированная система поддержки принятия решения о выборе режимов механической обработки тонкостенных деталей: свидетельство о государственной регистрации программы для ЭВМ № 2016663071.

20. Справочник технолога-машиностроителя. В 2 т. Т. 2 / под ред. А.Г. Косиловой, Р.К. Мещерякова. – М.: Машиностроение, 1986. – 418 с.

21. Гузеев В.И., Батуев В.А., Сурков И.В. Режимы резания для токарных и сверлильно-фрезерно-расточных станков с числовым программным управлением: справочник / под ред. В.И. Гузеева. – 2-е изд. – М.: Машиностроение, 2007. – 368 с.