Introduction. The refractory materials are of interest for high temperature applications in aerospace, nuclear and military industries, since they possess high melting temperature (> 2000 ?C). Molybdenum (Mo) is among these materials of high interest due to its excellent properties such as good thermal conductivity, high strength and toughness. The production of molybdenum is difficult due to its high melting point and the temperature of the ductile-brittle transition, therefore, in the production of this metal, powder metallurgy methods are mainly used. To implement these methods, it is necessary to have high-quality molybdenum powders, in particular, a high degree of purity and homogeneity of particle size distribution. One of the powder processing methods that is used to produce nano- and microsize powders, is the high energy kinetic milling. This cost-effective method is based on the friction and the high-energy collisions between the balls and the powder particles. And therefore, the purpose of the current work is to optimize the parameters of high energy kinetic milling for molybdenum powder. Optimization of processing parameters has a significant influence on the acceleration of the process of product formation, on subsequent sintering and achievement of the best mechanical properties of the final product. Optimization of milling parameters of Mo powder was achieved under different milling parameters including among others the rotation speed, the ball to powder weight ratio (BPR) and the milling time. Initially, the rotational speed was determined; it varied from 600 to 1200 rpm (where rpm are revolutions per minute). After this determination, milling parameters such as the milling time and the BPR were varied. The milling time ranged from 2 to 60 min and the BPR varied from 100:3 to 200:3. After that, influence of variable parameters on morphology and powder particles size distribution was investigated. The initial powder used in these experiments was Mo powder (particle size ~100 µm). The methods of investigation. Scanning electron microscopy and laser diffraction methods were used to estimate the particle size distribution. Results and Discussion. Particle size was decreased from 100 to 4 µm with increasing grinding time from 2 to 60 min. However, in each batch, a number of cold-welded particles measuring 200-400 μm was detected. These cold-welded particles were about 200-400 µm in size. As the result, the optimal milling parameters were: rotation speed of 900 rpm, BPR (200:3) and milling time of 60 minutes.
1. Neikov O., Naboychenko S., Murashov I.B., Yefimov A., Dowson G. Handbook of Non-ferrous metal powders: technologies and applications. Amsterdam, Elsevier Science, 2009, pp. 464–470.
2. Dean J.A. Lange’s handbook of chemistry. New York, McGraw-Hill Professional, 1998.
3. Davis J.R., ed. ASM speciality handbook. Heat resistant materials. Materials Park, Ohio, ASM International, 1997, pp. 361–364.
4. Ohser-Wiedemann R., Martin U., Seifert H.J., Müller A. Densification behavior of pure molybdenum powder by spark plasma sintering. International Journal of Refractory Metals and Hard Materials, 2010, vol. 28. iss. 4. pp. 550–557. doi: 10.1016/j.ijrmhm.2010.03.003.
5. Kim Y., Lee S., Noh J.-W., Lee S.H., Jeong I.-D., Park S.-J. Rheological and sintering behaviors of nanostructured molybdenum powder. International Journal of Refractory Metals and Hard Materials, 2013, vol. 41, pp. 442–448. doi: 10.1016/j.ijrmhm.2013.06.001.
6. Sheng Y., Guo Z., Hao J. Characterization of spherical molybdenum powders prepared by RF plasma processing. Advanced Materials Research, 2012, vol. 482–484, pp. 2563–2567. doi: 10.4028/www.scientific.net/AMR.482-484.2563.
7. Liu X.-P., Wang K.-S., Hu P., Chen Q., Volinsky A. Spheroidization of molybdenum powder by radio frequency thermal plasma. International Journal of Minerals, Metallurgy and Materials, 2015, vol. 22, iss. 11, pp. 1212–1218. doi: 10.1007/s12613-015-1187-7.
8. Garg P., Park S.-J., German R.M. Effect of die compaction pressure on densification behavior of molybdenum powders. International Journal of Refractory Metals and Hard Materials, 2007, vol. 25, iss. 1, pp. 16–24. Doi: 10.1016/j.jrmhm.2005.10.014.
9. Leitner K., Felfer P.J., Holec D., Cairney J., Knabl W., Lorich A., Clemens H., Primig S. On grain boundary segregation in molybdenum materials. Materials & Design, 2017, vol. 135, pp. 204–212. doi: 10.1016/j.matdes.2017.09.019.
10. An G., Sun J., Liu R.-Z., Li J., Sun Y.-J. Mechanical properties of molybdenum products prepared by using molybdenum powders with different micro-morphologies. Rare Metals, 2015, vol. 34, iss. 4, pp. 276–281. doi: 10.1007/s12598-013-0194-y.
11. Yang Ch., Zhou Y., Liu D., Jiang W., Liu F., Liu Z. Preparation of molybdenum powder from molybdenite concentrate through vacuum decomposition-acid leaching combination process. Rare Metal Technology. Cham, Springer, 2017, pp. 235–246.
12. Bolitschek J., Luidold S., O’Sullivan M. A study of the impact of reduction conditions on molybdenum morphology. International Journal of Refractory Metals and Hard Materials, 2018, vol. 71, pp. 325–329. doi: 10.1016/j.ijrmhm.2017.11.037.
13. Kim Y., Lee S., Noh J.-W., Lee S.H., Jeong I.-D., Park S.-J. Rheological and sintering behaviors of nanostructured molybdenum powder. International Journal of Refractory Metals and Hard Materials, 2013, vol. 41, pp. 442–448. doi: 10.1016/j.ijrmhm.2013.06.001.
14. Wang D., Yu Ch., Ma J., Liu W., Shen Z. Densification and crack suppression in selective laser melting of pure molybdenum. Materials and Design, 2017, vol. 129. pp. 44–52. doi: 10.1016/j.matdes.2017.04.094.
15. Ghayour H., Abdellhi M., Bahmanpour M. Optimization of the high energy ball-milling: modeling and parametric study. Powder Technology, 2016, vol. 291, pp. 7–13. doi: 10.1016/j.powtec.2015.12.004.
16. Liu M., Zhong X., Wang J., Liu Z., Qui W., Zeng D. Microstructure and thermal stability of MoSi2-CoNiCrAlY nanocomposite feedstock prepared by high energy ball milling. Surface and Coatings Technology, 2014, vol. 239, pp. 78–83. doi: 10.1016/j.surfcoat.2013.11.022.
17. Harris J.R., Wattis J.A.D., Wood J.V. A comparison of different models for mechanical alloying. Acta Materialia, 2001, vol. 49, iss. 19, pp. 3991–4003. doi: 10.1016/S1359-6454(01)00302-0.
18. Karthik B., Gautam G.S., Karthikeyan N.R., Murty B.S. Analysis of mechanical milling in simoloyer: an energy modeling approach. Metallurgical and Materials Transactions A, 2012, vol. 43, iss. 4, pp. 1323–1327. doi: 10.1007/s11661-011-0946-y.
19. Debata M., Acharya T.S., Sengupta P., Acharya P.P., Bajpai S., Jayasankar K. Effect of high energy ball milling on structure and properties of 95W-3.5Ni-1.5Fe heavy alloys. International Journal of Refractory Metals and Hard Materials, 2017, vol. 69, pp. 170–179. doi: 10.1016/j.ijrmhm.2017.08.007.
20. Suryaanarayana C. Mechanical alloying and milling. Progress in Materials Science, 2001, vol. 46, iss. 1–2, pp. 1–184. doi: 10.1016/S0079-6425(99)00010-9.
21. Ebrahimi-Kahrizsangi R., Abdellahi M., Bahmanpour M. Ignition time of nanopowders during milling: a novel simulation. Powder Technology, 2015, vol. 272, pp. 224–234. doi: 10.1016/j.powtec.2014.12.009.
22. Kiran U.R., Kumar M.P., Sankaranarayana M., Singh A.K., Nandy T.K. High energy milling on tungsten powders. International Journal of Refractory Metals and Hard Materials, 2015, vol. 48, pp. 74–81. doi: 10.1016/j.ijrmhm.2014.06.025.
23. Abdellahi M., Bhmanpour M., Bahmanpour M. Optimization of process parameters to maximize hardness of metal/ceramic nanocomposites produced by high energy ball milling. Ceramics International, 2014, vol. 40, iss. 10, pp. 16259–16272. doi: 10.1016/j.ceramint.2014.07.063.
24. Biyik S., Aydin M. The effect of milling speed on particle size and morphology of Cu25W composite powder. Acta Physica Polonica A, 2014, vol. 127, pp. 1255–1260.
25. Rzavi-Tousi S.S., Szpunar J.A. Effect of ball size on steady state of aluminum powder and efficiency of impacts during milling. Powder Technology, 2015, vol. 284, pp. 149–158. doi: 10.1016/j.powtec.2015.06.035.
26. Kilinc Y., Öztürk S., Öztürk B., Uslan I. Investigation of milling characteristics of alumina powders milled with a newly designed vibratory horizontal attritor. Powder Technology, 2004, vol. 146, pp. 200–205. doi: 10.1016/j.powtec.2004.09.031.
Funding:
This research has been financially supported by the Ministry of Education, Youth and Sports of the Czech Republic under the project CEITEC2020 (LQ1601).
Acknowledgements:
We also acknowledge CEITEC Nano Research Infrastructure (ID LM2015041) for providing us with access to its SEM devices.
Dycková L., Komarov P., Remešová M., Dycka M., Dvorák K., Menelaou M., Celko L. Optimization of molybdenum powder milling parameters. Obrabotka metallov (tekhnologiya, oborudovanie, instrumenty) = Metal Working and Material Science, 2018, vol. 20, no. 3, pp. 109–122. doi: 10.17212/1994-6309-2018-20.3-109-122. (In Russian).